Calculate straight line equation fitting the below data

Q: Compare and analyze plotting in Model space and in Layout Tabs. What are their advantages and…

A: every drawing in AutoCAD is having two-part both model space and layout tabs. By default we work on…

Q: To draw the figure below, the most :important command is Array O Trim O Сopy O Offset

A: Given data Grid of shape To be discussed Which command to be used

Q: 3b. Finally, a several datasets have been compiled and it is time to combine them. There is a…

A: Once all data is compiled, when combining data from different source with distinct coordinate system…

Q: Determine the coordinates of centroid for the given figure shown. 80 mm 50 mm Y 50 mm 150 mm X

A:

Q: For the truss shown in Figure 3, members AC and BC have cross sectional area of 2 in.² while members…

A:

Q: Show computations only for letter d.

A: Given:- SG=4 test slurry =200g solids /Lwater To find:- a)curve b)minimum cross-sectional area…

Q: Define integer ambiguities.

A: Answer The integer ambiguities are used in GPS & GNSS surveys.

Q: PROBLEM 3: A stadia measurement was undertaken with a theodolite having an internal focusing…

A:

Q: Calculate the volume between the two cross sections below. KM1+850 17 m2 23 m2 KM 2+050 10 m2 4 m2

A: From the given cross section we can sayAt station 1+850 and Area cut cm2| 17+23 = 402+050   End Area…

Q: Water discharging into a 10 m wide rectangular horizontal channel from a sluice gate is observed to…

A:

Q: - A spillway flood discharge of 22,100 m/s is simulated with a model in a laboratory provided with a…

A:

Q: A 25 mm wide, 1 mm thick strip is rolled to a final thickness of 0.6mm. It is noted that the strip…

A:

Q: H.W1 The beam is subjected to the linearly varying distributed load. Determine the maximum…

A: step 1-

Q: P6.1. Determine the reactions at the supports, the mag- nitude of the cable sag at point B, and the…

A:

Q: How to create stacked bar chart in tableau

A: This question is related to the Computer-aided design software from Civil Engineering. This is…

Q: p. Semantics is the. b. a. meaning of the data value of the data c. format of the data d. all of the…

A:

Q: Is there any simpler way to calculate this?

A:

Q: 4. Describe two steps that could be taken to reduce the likelihood of cavitation.

A: Note: As per the policy out of multiple questions only one questions can be answered. For other…

Q: Locate the centroid C(x,y) of the plane area shown below. Arrange your calculations in a tabular…

A: ###Locate the centroid of the plan area and make calculation in tabular format ####Centroid C

Q: AA County Foad c6o wie) For the rectangular shown, the county road is to be place such that the…

A: Given: The diagram is a rectangle.

Q: PROBLEM THEORY-10. A 4-m propped cantilever beam is loaded as shown in the figure. E = 200 GPa and I…

A:

Q: Equation method please

A: REACTION FORCE AT FIXED END: ∑FY=0RA-17-12×9×6=0RA=44 kips∑MA=0-MA+12×6×9×23×9+17×14=0MA=400 kips-ft

Q: Fluid mechanics This is not an assignmen. Give me right solution How you use conservation laws to…

A: To evaluate flow parameters we use couple of laws which are based on conservation of energy and…

Q: Q2. Calculate the force in each member of the loaded truss. A - 4 m B

A:

Q: 3. Reduce the following set of field notes and provide the math check. Station BS HI IS FS BM 101…

A:

Q: El is constant for the beam shown in Figure 4. • Compute the rotation of the beam at B. • Compute…

A:

Q: Length Line DIRECTIONS (meter) AB 500.65 Azs = 210° 1O' 50" BC 600.54 Azs = 149° 9' 35" CD 605.12…

A:

Q: i need all parts of question on the right hand corner solve I STATED FILL IN THE BLANKS.

A: Only 3 subparts can be answered at a time according to guildlines. Please resubmit the question…

Q: among the plans subjected to the given loads shown in Fig. 2, which plan exhibits the smallest…

A: Consider the given plan subjected to external load

Q: PLEASE PROVIDE CLEAR

A:

Q: P7.3. Determine the axial load, moment, and shear at point D of the three-hinged parabolic arch. 15…

A:

Q: cos a - sin Lsin a n a 1+ A = (1 – A)

A:

Q: Calculate the perimeter and the area of the triangles with the following dimensions (refer to Figure…

A: Given data- a = 10'0" a = 2750 mmb = 9'6" b = 2050 mmc = 3'0" c = 300 mmh = 2'0" h = 600 mm

Q: Estimated Immediate Aviy Activity Description Predecessors Duration (Weeks) 01 A Excevate B Lay the…

A:

Q: Calculate the following: Total area of the figure, in² xbar (location of the centroid along x axis),…

A: Area :A=A1+A2-A3A=4×10+12×5×10-π×32A=36.7256in2

Q: A thin sheet of rubber in the form of a square is uniformly deformed into the parallelogram shape as…

A: Given the figure of deformation of a thin sheet of rubber as,  The average normal strain along…

Q: Problem III. Determine the support reactions at B and the location of the maximum deflection for the…

A:

Q: Kindly include the free-body diagram too.

A: Solution: Given: Initial velocity u = 96 k,/hr u = 96×100060×60=36.67 m/s Final velocity: V = 0…

Q: A very long steel drill pipe got stuck in hard clay at an unknown depth. The drill pipe was applied…

A:

Construction Documents

Construction documents are the branch of architectural design and a vital field of the architectural process. We must not mistake the construction documents as a schematic design, wherein it involves sketching, model making, and so on. They provide guidance and instructions to the contractor or the subcontractor and they will study the architect’s building design, question the design professionals if needed, create a project manual and schedule for the successful construction of the proposed structure. Construction documentation acquires the detailed building permits and the design-build is initiated.