Q5/ A hot steam pipe having an inside surface temperature of 250 C has an inside diameter of 8 cm and a wall thickness of 5.5 mm. It is covered with a 9-cm layer of insulation having k =0.5 W/m. C, followed by a 4-cm layer of insulation having k =0.25W/m.C. The outside temperature of the insulation is 20-C. Calculate the heat lost per meter of length. Assume k =47 W/m. C for the pipe.

Q5/ A hot steam pipe having an inside surface temperature of 250 C has an inside diameter of 8 cm and a wall thickness of 5.5 mm. It is covered with a 9-cm layer of insulation having k =0.5 W/m. C, followed by a 4-cm layer of insulation having k =0.25W/m.C. The outside temperature of the insulation is 20-C. Calculate the heat lost per meter of length. Assume k =47 W/m. C for the pipe.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Kindly solve this question, Thank you so much
The given figure shows a thermal network with T01 = 325.15 K, T1 = 310.15 K, Rwall = 0.08 K/W, and Rconvy, 1= 0.036 K/W. Calculate the value of temperature T2 if the thermal network is under steady-state conditions. Tol Wall T2 T02
A 20 m metal pipe, with a thermal conductivity of 60 W/(m. K), is carrying pasteurised orange juice with a temperature of 80 °C. The pipe has an inside diameter of 90 mm and a wall thickness of 10 mm. To keep the orange juice at as high a temperature as possible, a 45 mm thick layer of fibreglass insulation is added to the pipe. This fibreglass has a thermal conductivity of 0.02 W/(m. K). If the the temperature outside the pipe is 15 °C, how much heat will be lost from the pipe? Assume that the conditions are steady-state. What is the resistance to heat flow in the metal pipe?: What is the resistance to heat flow in the fibreglass insulation?: What is the overall rate of heat flow from this insulated pipe? KIW W K/W
An oil flow through a 40 mm bore steel pipe with the thickness of 4 mm. The pipe is covered by 10 mm thickness of insulator with the thermal conductivity of 0.038 W/m.K as shown in Diagram 4b. The temperature of the oil in the pipe is 75°C and the ambient temperature is 17°C. The internal thermal conductivity of steel is 50 W/m.K and the inside and outside heat transfer coefficient are 300 W/m².C and 17 W/m?.C respectively. Neglecting radiation, calculate the following: i. Rate of heat flow per meter length of the pipe ii. The temperature of the outside surface (Ts). Ts Ambient Oil 75°C temperature 17°C 40 Note : All dimensions are in mm/Nota: Semua dimensi adalah dalam mm Diagram 4b/Rajah 4b
The oven of a stove must have a sufficient insulation so that the surface temperature of the stove is not greater than 50 oC. To accomplish this, insulation, k = 0.11 W/m-K, is used between the inside and outside metal surfaces. The room temperature is 20 oC, and the outside unit convective coefficient is 8 W/m2-K. Neglecting the resistance of the metal, what is the minimum thickness of insulation required, if the outside temperature reaches 315 oC?
Heat transfer
Consider a composite wall of overall height H = 30 mm and thickness L = 40 mm. Section A hasthickness LA = 15 mm and thermal conductivity of 3 W/(m·K). Sections B and C each have heightHB = 15 mm and thickness LB = 25 mm. The thermal conductivity is 1 W/(m·K) in section B and 2W/(m·K) in section C. The temperatures of the left and right faces of the composite wall are T1 =60°C and T2 = 30°C, respectively. The top and bottom of the wall are insulated. A) Draw a thermal circuit based on heat flux for the composite wall shown above.Assume that the temperature is uniform “vertically” in material A. Indicate thetemperatures, thermal resistances, and heat flux in the circuit diagram. Show theequations for the thermal resistances in the circuits. Do NOT need to perform anycalculations in this part.B. Draw a thermal circuit based on heat flux for the composite wall shown above.Assume that the temperature is NOT uniform “vertically” in material A and heat onlyflows along horizontal direction.…
7
QUESTION 3 A steel pipe 150mm external diameter conveys steam at a temperature of 260°C and is covered by two layers of lagging, each 50mm thick. The thermal conductivity coefficient of the inside layer of lagging is 0.0865W/mK while that of the outside layer is 0.0952W/mK. The outside surface temperature of the steel pipe can be taken as being the same temperature of the steam. The ambient temperature is 27°C and the heat transfer coefficient of the outside surface is 15W/m2K. Calculate: 3.1 the heat lost/hr for a pipe length of 30m;
2. A pipe with: ID: 130mm OD: 165mm k=15 W/m?-K L= 2m is insulated with several materials, and convection on the inside and outside of the pipe is as follows. Oil inside is at 118°C and air outside is at 25°C KA or h 10.256 W/m2-K Material Thickness A 25mm В 2.369 W/m2-K 30mm C 0.257 W/m2-K 40mm h=120.3T2/3 (T in K) h=0.272/3 (T in K) Oil inside Air outside Determine the heat losses of the pipe, and what must be the temperature of the oil to decrease the heat losses by 20%?
1. A pipe is covered with three insulation layers where the corresponding thicknesses are 150 mm, 250mm and 300mm and the respective thermal conductivities are 3.2 W/m°C, 2.1 W/m°C and 1.5 W/m C. The length of the pipe is 3m. The inner side of the pipe which has a diameter of 300 mm is exposed to a hot gas at 1000 °C with convection coefficient of 50 W/m2°C and the temperature of the inner side of the pipe surface is 800 °C. The air outside the pipe is at 25°C with a convection coefficient of 35 W/m2°C. a. Draw a schematic diagram which shows the heat transfer process b. Calculate the Heat transfer rate c. The overall heat transfer coefficient "U" of the system based on the inner pipe d. Temperature at each of the layers and at the outermost surface of the pipe.
Pressurized steam flows through a pipe of 0.6 m diameter. The pipe is embedded in a concrete block ,conductivity k = 1.4 W/mK ,with a square cross sectional length, w = 1 m. The required surface temperature values are 401 and 301 in K. Calculate the heat loss from the pipe per unit length. w Concrete T1 T2 D = 0.6 m