Calculate the heat loss through a 3-in. thick insulation board that has an area of 2- ft² and a k-value of 0.25. Assume the average temperature difference across the material is 70°F. Q = 11.66-Btu/hr Q = 10.99-Btu/hr Q = 10.66-Btu/hr Q = 11.99-Btu/hr Hide hint for Question 1 Utilize the (Q = k*A*AT/thickness) equation.

Calculate the heat loss through a 3-in. thick insulation board that has an area of 2- ft² and a k-value of 0.25. Assume the average temperature difference across the material is 70°F. Q = 11.66-Btu/hr Q = 10.99-Btu/hr Q = 10.66-Btu/hr Q = 11.99-Btu/hr Hide hint for Question 1 Utilize the (Q = kAAT/thickness) equation.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.39P

See similar textbooks

Similar questions

i need the exercise 2.4 please show details. thermal conductivity value of the insulation IS 0.021 Btu/hft2°F
An office space contains one (6`x 3`) well- fitted door made of nominal 2" wood. The heat loss through door is (517.2 Btuh) if Tb.l.=80 F and To= -10 F. ? True or false
The cooling load for a house is determined in part by using the same formulaused to find the heat load. The temperature difference used in designing acooling system is 25°F. The corner room shown does not face the sun so noadditional cooling load is required. The windows are single pane, and thewalls are brick veneer with 31⁄2 inches of insulation (R-11). The ceiling has31⁄2 inches of insulation (R-11), and the floor has no insulation. The room isbuilt over a vented crawl space with a vented attic above it. Find the coolingload for this room.
i need the answer quickly
An office space contains one (6`x 3`) well- fitted door made of nominal 2" wood. The heat loss through door by infiltration is (3381 Btuh) if Tb.l.=80 F , To= -10 F , and Vwind=15 mph ? True or false
Calculate the heat loss per linear ft from 2 in. nominal pipe (2.375 in. outside diameter)covered with 1 in. of an insulating material having an average thermal conductivity of0.0375 Btu/hr-ft-F. Assume that the inner and outer surface temperatures of the insulationare 380 °F and 80 °F respectively.
Find the thermal resistance r (in hr - °F/BTU) and the equivalent R-value (in hr ft?. °F/BTU) of a typical frame 20' x 7.5" wall consisting of a 0.5" plaster board on the inside of the room, nominai 2 x 4 studs, and a 0.5" sheathing on the outside. The spaces between the studs are filled with an R-15 insulating foam. What is the heat loss (in BTU) through this wall in four hours if the inside temperature is 72°F and the outside temperature is 32°F? (Assume that the 15% of the wall's area are studs and the remaining 85% is filled with the insulating foam. Assume that the air is moving outside the wall.) r= 0.0805 x hr: OF/BTU R=0.09 x hr ft2. F/BTU AQ = BTU
2. Calculate the heat loss for the structure described below. Use the indoor design setpoint of 70°F. ● . . . ● ● Hint: Utilize the Q=U*A*(ti-to) & Q = U'*P*(ti-to). Make sure to reference the following tables and examples to help assist you solve this problem; Table 5-5a, Table 5-8, Table 5-4a, Example 5-3, Eq. 5-23, and Fig 5-8. Given: i. Location: Des Moines, IA @ 99% winter OAT ii. Walls: Table 5.7, Construction 2 iii. Floor: Concrete slab with 2-ft, R-5.4, vertical edge insulation iv. Windows: Double-Insulating Glass; 1/4-in. air space; e = 0.6 on surface 2, 3x4-ft, double hung, reinforced vinyl frame; three on each side v. vi. Roof-Ceiling: Same as Example 5.3, height of 8-ft vii. House Plan: Single story, 36-ft x 64-ft Doors: Wood, 1-3/4-in. panel doors with metal storm doors, three each, 3x6.75-ft Qwindows = Qdoors= Qwalls = Qroof/ceiling= Qfloor = QTOTAL = Btu/(hroft²0F) Btu/h Heat Loss Btu/h Heat Loss Btu/h Heat Loss Btu/h Heat Loss Btu/h Heat Loss
6. Make a diagram and show the step-by-step process. Do not use shortcut methods. Make it as detailed as it can be. Encode (not hand-written)! DO NOT COPY CHEGG'S ANSWER
Q2/ An insulated steam pipe having an outside Steam pipe diameter of 30 mm is to be covered with two Better ination (4) Paer ination () layers of insulation, each haying thickness of 20 mm. The thermal conductivity of one material is 5 times that of the other. Sm L 1. Assuming that the inner and outer surface temperatures of composite insulation are fixed, how much will heat transfer be increased when better insulation material is next to the pipe than it is the outer layer?
5. A pipe with an outside diameter of 2.5 inches is insulated with 2 inches layer of asbestos (k = 0.396 Btu- in/hr-ft²-°F), followed by a layer of cork 1.5 inches thick (k = 0.30 Btu-in/hr-ft²-°F). If the temperature at the inner surface of the pipe is 290°F and at the outer surface of the cork is 90°F, calculate the heat loss per 100 ft of insulated pipe. (Btu/hr)
An oil storage tank has 20mm steel walls covered with 50mm of fiber glass insulation. if the oil temperature is kept at 150 degree Celsius, what is the rate of heat loss when the outside temperature is 20 degree Celsius and external air coefficient is 20W/m². How much would the heat loss be reduced by doubling the thickness of the insulation?