Q4\Find the type of damping in this system Where: m=5kg, K = 1500 N/m Damping coefficient= 1.5 *105 N-seC/m Q5\ 1. When E=1 that is mean : A. Overdamped system B. Critically damped system C. Underdamped System 2. The total time of a 20 cycle was 20.5 sec What is the time of one суcle: A. 0.975 В. 1.025 С. 1.5

Q4\Find the type of damping in this system Where: m=5kg, K = 1500 N/m Damping coefficient= 1.5 *105 N-seC/m Q5\ 1. When E=1 that is mean : A. Overdamped system B. Critically damped system C. Underdamped System 2. The total time of a 20 cycle was 20.5 sec What is the time of one суcle: A. 0.975 В. 1.025 С. 1.5

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Solve!
3. For the motor, load and torque-speed curve, find the transfer function, G(s) = 0L (s)/Ea(s). T (N-m) + ea(t) Ra www J₁ = 4 kg-m² N₁ = 50 D₁ N₂ = 150 D₂ = 36 N-m-s/rad 8 N-m-s/rad ½₂-36 kg-m² OL(1) 150 50 V 100 w (rad/s)
A coil with 120 turns effected by variable magnetic field which is decreased by 40µwb per second, the magnitude of the * ----induced emf is a. 4.8 mv (O b. - 4.8 mv O c. 4.8 v O
from the equation below, where did the -0.5 and j0.1768 came from? can you show the computation? Thank you!
Problem #7) Specify whether each of the statements are TRUE or FALSE. D Reactive Power is a measure of the average power consumed by reactive (capacitive and inductive) loads. When connected to an AC voltage source, the instantaneous power (rate of energy transfer) supplied to a resistor varies at a frequency that is 2x the frequency of the applied source voltage. The magnitude of the impedance of a capacitor supplied by an AC source will increase as the source frequency increases. An AC source that has an RMS magnitude of 100V will supply the same average power to a resistor compared to a 100V DC source. The voltage across a capacitor is proportional to the rate of change of the current flowing through the capacitor. The magnitude of the impedance of a resistor supplied by an AC source does not vary as the source frequency increases. A complex impedance Z=R+jX, that has non-zero resistive and reactive components, will consume both real and reactive power when supplied by an AC source.…
???
Kindly draw the circuit and diagram for this problem and solve step by step process. Thanks and it will help a lot. Have a nice day expert!
• T or F, modify the wrong part if False, please underline twice your answer if True or False. A cumulatively-compound DC machine has its flus for the shunt and series field winding flow in opposite directions.
This question please
Please solve this question in control system quickly
Place your final answers for this problem in the correct boxes at the bottom of the next page. Use the value Zdegrees notation for representing phasors. Bold terms are expected to be phasors. Tek Run 1 5.00 V 8 4.00ms +6.68000ms 4 H a b 3.29ms 20.0ms A16.7ms (2.50MS/S 100k points The voltage pictured in the image above is applied to a load with an impedance of Z=3+j5. The load has two components, in series. 1 1. What is Vmag and Vrms. Assume that the phase of the pictured waveform is degrees. 2. Calculate Irms. 3. Calculate S, the complex power. Trig'd 9.425 V 9.429 V A3.906mV s 3.00 V 4. Calculate average power, apparent power, reactive power, and power factor. It isn't necessary to list if the power factor is leading or lagging. 5. What component values are used to make the resistive and reactive components of the load?
Where N =5 ,theta=45 , the value of load reactance =1.5 What is the load power factor?