Q4. Two plates have a length (L) and thickness (t), were welded together. Assume these plates have similar material properties. For the same welded length, which is better to use the single transverse lap joint or the single butt joint and why? Q5. Design the rectangular key which is used to connect between 50 mm shaft and pulley. Assume the key material has same properties of the shaft material. Determine shaft strength factor if the length of the key should not exceed 12 cm.

Q4. Two plates have a length (L) and thickness (t), were welded together. Assume these plates have similar material properties. For the same welded length, which is better to use the single transverse lap joint or the single butt joint and why? Q5. Design the rectangular key which is used to connect between 50 mm shaft and pulley. Assume the key material has same properties of the shaft material. Determine shaft strength factor if the length of the key should not exceed 12 cm.

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter22: Welding Joint Design And Welding Symbols

Section: Chapter Questions

Problem 4R: Sketch a V-grooved butt joint, and label all of the joint's dimensions.

See similar textbooks

Similar questions

A pulley is keyed to a 28 mm steel shaft with a 7 mm x 8 mm x 20 mm key. If the hub length is 20 mm and the allowable crushing stress for the key material is 105 MPa, How much torque can be transmitted in kN-m?
can I got please the answer of these please
3. An M16 x 2 bolt with a slotted hex nut is used to clamp together two 25 mm steel plates. The joint is assembled with a size 16 N washer underneath the bolt head. The bolt is a 5.8 class metric grade, with a proof strength of 380 MPa. The joint is intended to be permanent. Determine a suitable length for the bolt, rounded up to the nearest standard size in millimeters. Calculate the bolt stiffness, the elongation of the bolt after the necessary preload is developed, and the bolt torque required to apply the preload. Assume that coefficients of friction between the bolt, nut, and collar are all ~0.15. For steel, use E = 207 GPa. Standard threaded fastener lengths, dimensions of hexagonal nuts, and dimensions of metric plain washers are provided in the textbook appendices.
A 3/8-18 grade 8 bolt has 800 pounds of force pulling on it. Find the tensile force, the thread stripping strength for the needed length of engagement and the factor of safety for the bolt with that amount of force.
BA TECHNICA In a flange coupling as shown each shaft is keyed to the both of a flange with a sunk key to transmit(30) H.P. at (300) r.p.m. The design shear stress for the shaft and key is (450) N/mm and the number of bolts connect the halves are (5). The design tensile stress for the bolts is(700) N/mm2 and crushing stress for, key is (900) N/mm. Design the shaft, When the bending moment equal to (400) N.m. Flange اقراص إقران مرنة Hub Key Shaft 1.6 d O mm Kay عمود محور امتطالی
Question No.15: Design muff coupling to connect two steel shafts transmitting 40 kW at 350 rpm. The material for shafts and key is plain carbon steel for which allowable shear and crushing stresses are 40 MPa and 80 MPa respectively. The material for muff is cast iron for which allowable shear stress is 15 Mpa
Find the size of 14 bolts required for C.I.steam engine cylinder head. The diameter of the cylinder is 400 mm and the steam pressure is 0.12 N/mm.
The two lever assembly shown below is subject to a static load F = 8250 lb. %3D (a) identical links BD can be made from based on the stress in the middle of each link. Specify the lowest-strength alloy steel from Appendix A-10 that the two (b) is the minimum recommended diameter that the pins can be machined to? The pins at B and D are made from SAE 4140 OQT 900 alloy steel. What What is the bearing stress on the pins at B and D based on the pin (c) diameter you calculated in part (b) above? 9 in 8 in C B Top View A В C B 0.75 in - -0.31 in F 0.31 in Side View Front View
A 80 mm steel shaft develops 5 kN - m torque and using a flat key to fasten a 250 mm pulley. The crushing stress of the key is 50 MPa. The key has a width and length of 20 mm and 150 mm, respectively. What is the key thickness? A. 21.15 mm B. 26.86 mm C. 33.29 mm D. 36.48 mm
repeat problem 8-19 with the bottom aluminum plate replaced by one that is 20 mm thick.
A part of a latch for a car door is to be made from a circular rod. With each actuation, it sees a tensile force that varies from 780 to 360 N. Small size is important. Complete the design, and specify a suitable shape, material, and dimensions for the rod.
Read carefully. Please solve ellaborately and include the untis in every step, and write your solutions clearly and readable if your solution is in written form, Your work will be appreaciated much. Thank You! The area of American, UNC bolt is 0.61i .in2 with pitch of 5mm. A. What is the bolt nominal diameter, mm? B. The bolt designation.