3. An M16 x 2 bolt with a slotted hex nut is used to clamp together two 25 mm steel plates. The joint is assembled with a size 16 N washer underneath the bolt head. The bolt is a 5.8 class metric grade, with a proof strength of 380 MPa. The joint is intended to be permanent. Determine a suitable length for the bolt, rounded up to the nearest standard size in millimeters. Calculate the bolt stiffness, the elongation of the bolt after the necessary preload is developed, and the bolt torque required to apply the preload. Assume that coefficients of friction between the bolt, nut, and collar are all -0.15. For steel, use E = 207 GPa. Standard threaded fastener lengths, dimensions of hexagonal nuts, and dimensions of metric plain washers are provided in the textbook appendices.

3. An M16 x 2 bolt with a slotted hex nut is used to clamp together two 25 mm steel plates. The joint is assembled with a size 16 N washer underneath the bolt head. The bolt is a 5.8 class metric grade, with a proof strength of 380 MPa. The joint is intended to be permanent. Determine a suitable length for the bolt, rounded up to the nearest standard size in millimeters. Calculate the bolt stiffness, the elongation of the bolt after the necessary preload is developed, and the bolt torque required to apply the preload. Assume that coefficients of friction between the bolt, nut, and collar are all -0.15. For steel, use E = 207 GPa. Standard threaded fastener lengths, dimensions of hexagonal nuts, and dimensions of metric plain washers are provided in the textbook appendices.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Ball bearings are rated by a manufacturer for a life of 106 revolutions. The catalogue rating of a particular bearing is 16 kN. If the design load is 2 kN, the life of the bearing will be Px 106 revolutions, where Pis equal to
Two gas struts with a extended length of 26", compressed length of 16" and a stroke of 10" with a .39" rod and .866" body is being used to hold a door weighing 40 lbs. prior to use, the owner would like to ensure the ball bearings can hold the load of the gas struts closed. The gas strut is a 20 lb compression gas strut, how much force does it take to keep gas strut closed if you were to push straight down in order to compress. Note: The answer is not 20lbs and I need all equations.
For a bolted assembly, the stiffness of each bolt is ka = 700 MN/m and the stiffness of the members is km = 2100 MN/m per bolt. The joint is subject to occasional disassembly for maintenance and should be preloaded accordingly. An external load is applied to the entire joint with P = 360 kN. Assume the load is equally distributed to all the bolts. It has been determined to use M12x1.75 grade 8.8 bolts with rolled threads. (a) Determine the minimum number of bolts necessary to avoid yielding of the bolts. (b) Determine the minimum number of bolts necessary to avoid joint separation.
Find the distance ( mm ) measurement between preload and major load position of the Rockwell Hardness Number 50HRC
A 2.5-in Aluminum plate and a 1.5-in cast-iron plate are compressed with one bolt and nut. The bolt is 3/8 in-16 UNC. (1) Determine a suitable length for the bolt, rounded up to the nearest 4 in. (2) Determine the bolt stiffness ks. (3) Determine the stiffness of the members km.
150- 18 F = 25 KN 25 200 25 + 25 € 100- -25 25 50 4 For the bracket and loading condition shown above, determine the smallest size Grade 8.8 metric bolt needed to hold the bracket in place that will still provide a minimum factor of safety of 2 versus the proof strength of the bolt. Assume coarse threads. Neglect the vertical shear on the bolts. All dimensions are in millimeters.
Required information For a bolted assembly with six bolts, the stiffness of each bolt is kb 2 Mibf/in and the stiffness of the members is km = 13 Mlbf/in per bolt. An external load of 80 kips is applied to the entire joint. Assume the load is equally distributed to all the bolts. It has been determined to use 1/2 in-13 UNC grade 8 bolts with rolled threads. It is desired to find the range of torque that a mechanic could apply to initially preload the bolts without expecting failure once the joint is loaded. Assume a torque coefficient of K = 0.2. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the maximum bolt preload that can be applied without exceeding the proof strength of the bolts once the load is applied. The maximum bolt preload that can be applied is Ibf.
3.) The diagram below shows a 5.5m long double angle brace which is connected by 6mm welding connection. The length of weld shown in the picture is 300 mm on the top and 100 mm on the bottom. The 2-L127x 89x6.4 are 300W steel and long leg back-to-back. The braces are to be welded to a 12 mm 350W steel gusset plate. Determine the factored tensile capacity of the angles. Any intermediate connections that are required should also be specified. 740 kN -12 mm Gusset Plate
help me with number 10,12 and 13.