Q4. The pin-connected frame is subjected to the force Fas shown. The dimensions are /₁ = 3.8 m, /2 = 2.8 m, and angle = 71°. Member AB is made of steel (E = 200 GPa), and has rectangular cross-section, with b = 28 mm and h = 67 mm The supports at A and B act as pins for x-x axis buckling and as fixed supports for y-y axis buckling. Determine the greatest load F(in the unit of kN) the beam will support without causing member AB to buckle. h B F Xy 22m- 0 y -b y h Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point.

Q4. The pin-connected frame is subjected to the force Fas shown. The dimensions are /₁ = 3.8 m, /2 = 2.8 m, and angle = 71°. Member AB is made of steel (E = 200 GPa), and has rectangular cross-section, with b = 28 mm and h = 67 mm The supports at A and B act as pins for x-x axis buckling and as fixed supports for y-y axis buckling. Determine the greatest load F(in the unit of kN) the beam will support without causing member AB to buckle. h B F Xy 22m- 0 y -b y h Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Angled member ABC is supported by being pinned to a collar on a smooth rod at A, a roller at B, and weightless link CD. It is subjected to a force of F = 3 kN and a couple moment of M = 3.4 kN * m as shown. Other dimensions are given: w1= 3.4 m w2= 5.9 m h = 2.7 m 01 = 40 degrees 02 = 55 degrees F D 02 M W1 W2 i. Determine the magnitude of the reaction force at pin A. ii. Determine the magnitude of the reaction force at roller B. iii. Determine the magnitude of the force in member CD.
For the truss shown in Figure 2.3b, determine the force in member DO if x = 4 m, y = 3 m and P = 9.6 kN. Indicate whether the member is in tension or compression. (Note: Use negative sign (-) if the member is in compression.) 7 panels at x m = 7x m В I K L E y F A х М N H P P kN P kN
a b c d F 5 m 1.5 m 2.1 m 2.4 m 26 kN The structure above is subjected to a load at point C. Using the table below, determine the forces acting at the support pins and at pin B on member ABC. Forces: (Denote tension forces with positive values; compressive forces with negative values.) FAX = ? FAY = ?
Question 1. RAX A 0 RAY F₁ Enter FAP: KN F KN E F₂ D The figure above is a pin-joint frame with angle 8 = 50° between members AF and AB. (Note that the diagram is not to scale). Given that the reaction forces at the support A are given by RAx = 70kN and RAY = 30kN, calculate the forces in members AB and AF, denoted by FAB and FAF respectively. Enter your answers in kilonewtons (kN) correct to 2 decimal places in the boxes below: Enter FAB RDY 4 [6 m
A new art exhibit featuring mobile works is going up in the Norwalk, CA area. One art work is shown in the figure below. A 105 N uniform beam is pinned to the ground by a pivot. The beam is supported by a cable (attached 3/5 from the bottom of the beam) to allow for each of the shoes to hang freely. Each individual shoe has a weight of 7.5 N. 10 WALL FLOR (a) ( If one shoe is attached 1/7 of the way up the beam and another shoe is attached 5/8 of the way up the beam, with e, = 70.1° and e, 30.1°, what is the tension in the cable, in newtons? %3! %3D (b) What is the x-component of the force, in newtons, that the pivot exerts on the bottom of the beam? (c) O What is the y-component of the force, in newtons, that the pivot exerts on the bottom of the beam?
The L bar is supported by a universal gasket at O and by the two wires as shown. The universal joint can withstand, in addition to the three reaction forces, a moment on the y axis but not on the x and z axis, find the reactions for when the load is in x = 1 m. (b) 1.2 m 1.8 m 0.3 m. 0.6 m E B 2.1 m -1.5 m 50 kg
Consider a steel cube with side length L and each of its faces normal to the orthogonal axes x, y, and z as shown below. If the cube is subjected to a constant tensile force T along the x-axis and the faces along the y- and z- axes are left free and unsupported, which of the following best describes what is expected to happen? Z Select one: O A. The cube will expand along the x-axis and compress along the y- and z-axes. B. The cube will expand along the x- and y-axes and will not deform along the z-axis. O C. The cube will expand along the x-axis and will not deform along the y- and z-axes. O D. The cube will compress along the x-axis and expand along the y- and z-axes.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F₁ = 31 kips, F₂ = 11 kips, F3 = 22 kips, and F4 = 36 kips, determine the absolute value of the axial load in rod (2). F A F₂ (1) F₂ B F3 C (3) D O 16 kips O 12 kips O 7 kips O 9 kips O 22 kips
The frame shown in the figure is supported by a hinge at A and a frictionless wheel F. When P = 12 lb, determine (a) the reactive forces at support A and the bottom of the wheel F, and (b) forces applied to member ABCD. ABCD is a single member. So is CEF. Points B, C, and E are pin joints. P 12 in 6 in. 6 in. 60 lb-in B 4 lb/in C 6 in. 4 lb/in
The shaft is supported at its ends by two bearings A and B and is subjected to the forces applied to the pulleys fixed to the shaft. ( Figure 1) The T₁ = 410-N forces act in the -z direction and the 200-N and 80-N forces act in the +y direction. The journal bearings at A and B exert only y and z components of force on the shaft. Figure X 200 mm 300 mm 150 mm 150 mm 200 mm D 400 mm B 200 N 200 N Z 80 N 80 N 1 of 1 > ▾ Part B ▾ Determine the resultant shear force in the y direction on the cross section at C. Express your answer to three significant figures and include appropriate units. (Vc), = 245.71 ▾ Part C Submit Previous Answers Request Answer * Incorrect; Try Again; 4 attempts remaining Submit (Vc), = Value Part D Determine the resultant shear force in the direction on the cross section at C. Express your answer to three significant figures and include appropriate units. T= HA Submit Part E ריהם Determine the resultant torque on the cross section at C Express your answer to three…
The compound beam shown in (Eigure 1) is fixed at E and supported by a rocker at A and B. There are hinges (pins) at C and D. The 4-kN load is applied just to the right of the pin at D. Suppose that w = 5 kN/m. Figure 4 kN 6kN I. conf 1 of 1 -2m-2m-2m-3m- 3m ▼ Determine the y component of reaction at A. Express your answer to three significant figures and include the appropriate units. A₁ = Value Submit Part B B, = HA Submit Part C Request Answer Determine the y component of reaction at B. Express your answer to three significant figures and include the appropriate units. Value KN Request Answer ? KN ? Determine the component of reaction at E.. Express your answer to three significant figures and include the appropriate units.