The truss below is subject to the loads as shown. All of the members are attached at plates and can be treated as pin connected. The truss is attached to the ground with a pin joint at A and a roller at E. The applied load H is 335 lb. The applied load J is 211 lb. What is the internal resultant normal force in member CD in lb? (tension is positive, compression is negative)

The truss below is subject to the loads as shown. All of the members are attached at plates and can be treated as pin connected. The truss is attached to the ground with a pin joint at A and a roller at E. The applied load H is 335 lb. The applied load J is 211 lb. What is the internal resultant normal force in member CD in lb? (tension is positive, compression is negative)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

See the truss shown below, supported by pins at A and G. Determine the force in members BC, CF, and FE, and state whether each of these three members is in tension (T) or compression (C), or whether any of them are zero-force members (ZFMS). Provide Given, Find, Assumptions, Problem Type/Features, FBDS, Calculations, and Conclusions in your solution. C 4 m E D 3 m 3 m 3 m 10 kN
Problem 3 The boom AB supports a load of W = 720 lb. The boom is supported by a ball-and-socket joint at A and by two cables, BC and BD. Find the tension in each cable and the axial force in the boom, assuming that point C is 4 inches vertically above the position shown in the figure and the other dimensions are unchanged. Neglect the weight of the boom. -9 in.- 8 in. B 12 in. W = 720 lb %3D
Determine the force in members BC, GA, and BG of the truss shown in the figure below. Let P = 175 kN. NOTE: If your answer is a compressive force then just put a negative sign. If your answer is a tensile force then just type the answer directly. (ALSO, DON'T FORGET THE UNITS) 2P 2P 30 60V60° B 60 60° 30 3P 4m 4m 4m Solve the force in member BC. Solve the force in member GA. Solve the force in member BG.
The illustrated truss is subject to certain loads. Calculate the forces acting in the components identified as 3-4, 3-10, and 9-10. Attach your solution (Give, Required, Solution with FBD) 0.8 kip 1.6 kips 2 8 ft 8 1.6 kips 3. 1.6 kips 8 ft 4 8 ft 10 1.6 kips 8 ft 5 1/1 1.6 kips 8 ft 6- 12 0.8 kip 6 ft 8 ft 4.5 ft
m 4: The maximum force any member can support is 24 kN in tension and 35 kN in compression, determine the largest permissible mass "m" which may be supported by the truss. Hint: use the method of joints to calculate all of the member forces in terms of the weight (say "w"); then choose the largest positive and negative member forces to determine m = w/g. There is a "rocker" support at "E"; this is the same as a roller support. A E 4 m B D 4 m 30° m
A new art exhibit featuring mobile works is going up in the Norwalk, CA area. One art work is shown in the figure below. A 105 N uniform beam is pinned to the ground by a pivot. The beam is supported by a cable (attached 3/5 from the bottom of the beam) to allow for each of the shoes to hang freely. Each individual shoe has a weight of 7.5 N. 10 WALL FLOR (a) ( If one shoe is attached 1/7 of the way up the beam and another shoe is attached 5/8 of the way up the beam, with e, = 70.1° and e, 30.1°, what is the tension in the cable, in newtons? %3! %3D (b) What is the x-component of the force, in newtons, that the pivot exerts on the bottom of the beam? (c) O What is the y-component of the force, in newtons, that the pivot exerts on the bottom of the beam?
For the frame shown in the below Figure, determine the horizontal and vertical components of the hinge force at B as it acts upon member AC.
Itranscript Required Information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. The truss shown consists of six members and is supported by a short link at A, two short links at B, and a ball-and-socket at D. Consider load of 420 lb applied at C. 10 ft Bol 24 t Determine the force in each of the members. The force in member AC (FAC) is The force in member BC (FBC) is The force in member CD (FCD) is The force in member AB (FAB) is The force in member BD (FBD) is The force in member AD (FAD) is Ib(Click to select) lb (Click to select) ✔ lb (Click to select) V lb (Click to select) b(Click to select) V lb (Click to select) V
Determine the force in each member of the truss shown in (Figure 1). State if the members are in tension or compression. Take that P = 420 lb. Express your answer to three significant figures and include the appropriate units. Assume positive scalars for members in tension and negative scalars for members in compression. Given: angle to use is 36.9 degrees, FCD = 700lb FAD =-560lb Find: a) Determine the force in the member BC of the truss, and state if the member is in tension or compression. b) Determine the force in the member AC of the truss, and state if the member is in tension or compression. c) Determine the force in the member AB of the truss, and state if the member is in tension or compression.
4. Consider the truss shown in the Figure 6 below: 250 KN C 100 KN 450 450 5m Figure 6 a. Calculate the reactions at joints A and B b. Using the method of joints, calculate the forces in members AB, AC and BC. с. State if the forces are in tension or compression
For the pinned frame in the figure, calculate the pin forces acting at point B, on member BD (magnitude and direction).Hint: Look for two-force members
3. The frame shown in the figure is supported by a hinge at E and a roller at D. Compute the horizontal and vertical components of the hinge force at C as it acts upon BD. 24 kN -2m- 1m- 4m