30° A, C В ●I•I• The truss above is supported by a roller at point A and a pin at point C. Which of the following is closest to the force in member BC? O a) 11.5 kN (T) O b) 34.6 kN (T) c) 30.0 kN (T) d) 69.3 kN (T)

Q: A 5-m-long simply supported timber beam carries two concentrated loads as shown. If L = 22 kN and M…

A:

Q: The frame shown is fitted with three 45 cm diameter frictionless pulleys. A force of F= 575 N is…

A: The dimension are The force applied is The angle is

Q: Refer to the diagram. a) Determine the horizontal and vertical components of force which the pin at…

A:

Q: 40 kN -2 m- -2 m D 30° А, C В The truss above is supported by a roller at point A and a pin at point…

A:

Q: Q2: The structure shown in the diagram ( one ofthe two identical structures that support the scoop…

A: We need to draw FBD and resolve forces first

Q: Part A 6 ft Ax= -106.7 lb, Ay = 80.0 lb Ax-46.7 lb, Ay = 45.0 lb Ax-53.3 lb, Ay = 40.0 lb O Ax Ax =…

A: Determine the horizontal and vertical components of force at pin A.

Q: Prob 4) Solve for the force in member HG and state whether in tension or compression A B 20 k 40 ft…

A: Force in member HG and check whether it is in Tension or compression

Q: A) Determine the forces acting on piece DG. Show your free body diagrams. W = 800 lbs.

A:

Q: 2) Consider the truss shown below. The truss is subjected to a vertical load (P) at joint E.…

A: As per unit load method, the procedure is,i) introduce a virtual load (of 1 force unit) along the…

Q: Determine: a) The magnitude and direction of the reactions at 3 and 5 b) The forces in each member…

A: Given: Find:a The magnitude and direction of the reactions at 3 and 5b The forces in each member of…

Q: Since it is such a beautiful day, Silly Sam is on a swing instead of being at the office.  The swing…

A: Given data, Diameter of the bolt connecting the cable to the clamp, dbcc = 25 mm = 0.984 in Diameter…

Q: TRUSS PROBLEM Determine: a) The magnitude and direction of the reactions at 3 and 5 b) The forces…

A: To find - a) The magnitude and direction of the reactions at 3 and 5. b) The forces in each member…

Q: A) Mark each of the zero-force members in the truss with an X. Answer -3 ft F 500 lb 3 ft- E B -3…

A: (A) To find: The zero force member in the truss with an X. FBD: The free body diagram is,

Q: P a 3 a 4 B a 4 а Which of the following is closest to the force in member CD? O a) o O b) -0.707·P…

A:

Q: Which free-body diagram(s) can be used to solve the internal forces at point D (in the middle of the…

A:

Q: For the truss shown, a) find the load in member GH using the method of sections, and  b) indicate…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.