TRUSS PROBLEM Determine: a) The magnitude and direction of the reactions at 3 and 5 b) The forces in each member of the truss and determine if the truss is being subjected to a compressive or tensile force. answers: a)R3 = 75 vertically upwards, R5 = 25 vertically upwards b)F1-2 = -29, F1-3 = -87, F1-4 = -29, F2-4 = +29, F2-5 = -29, F3-4 = +43, F4-5 = +14

Q: F=2580 Ib 4 5 A 28 ft

A: Draw the free-body diagram of the beam, Resolve the Force F=2580 lb into two components,…

Q: The truss is shown. Indicate direction to your final answer.   a.) What is the vertical reaction…

A:

Q: Q3) Determine the components of reaction at the roller support A and pin support C. Joint B is fixed…

A:

Q: F₁ F₂- F₂ A B с F3 -F3 D E F

A: Given Data:Applied forces: F1 (unknown), F2 = 11 kN, F3 = 9 kN, F4 = 6 kNDiameter at section B (dB)…

Q: A block of mass 40 kg is resting on an inclined surface as shown in figure 4. A) Draw the free body…

A: Given:- M=40kg Angle = 25 degree To find:- a) Free body diagram of block b) Conditions for static…

Q: Problem 6.2 Rigid Body Equilibrium The tailgate of the vehicle is only supported by a single cable…

A: According to the given data Weight of the blobk=WB=32x9.81=313.92N Weight of the…

Q: 2. For the crank-slider machine shown below, the collar at A is frictionless. The vertical applied…

A:

Q: (question 1)          P = 75 lb. The pin at C is attached to member ABCD and passes through the…

A: Given data :- P = 75 lbDetermine :-Part A) Determine the horizontal and vertical components of force…

Q: A rigid beam of negligible weight is supported by a hinge at A and a rocker at B as shown in the…

A: Given:F=16 KN

Q: A 1.5 m B P₁ C -1.5 m 1.5 m- D F P₂ -1.5 m 2 m

A:

Q: A) Mark each of the zero-force members in the truss with an X. Answer -3 ft F 500 lb 3 ft- E B -3…

A: (A) To find: The zero force member in the truss with an X. FBD: The free body diagram is,

Q: Q4) Structural Analysis This bridge is made of two-force members attached at the ends. All angles…

A:

Q: C P 100 mm Bo8 kg 200 mm 25° 8 kg

A:

Q: 4) Use the method of sections to find the true magnitude and direction of the force in member AB of…

A:

Q: Determine the force in each member of the  truss, and state if the member is in tension or…

A: For the solution refer below images.

Q: ) P1=13 kN and P2= 6.5 kN. Compute reaction at B. b)P1=13 kN and P2= 6.5 kN. W= 27.5 kN is applied…

A:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.