Determine: a) The magnitude and direction of the reactions at 3 and 5 b) The forces in each member of the truss and determine if the truss is being subjected to a compressive or tensile force. c) Comment on your answers answers: Q1 R3 = 50 vertically upwards, R5 = 50 vertically upwards F1-2 = -29, F1-3 = -58, F1-4 = 0, F2-4 = 0, F2-5 = -58, F3-4 = +29, F4-5 = +29

Q: B 45° 45° Weight = P A post with a horizontal and inclined member supports a box whose weight is P,…

A:

Q: QS/ Replace the three forces which act on the bent bar by a force-couple system at the support point…

A: In a force system, The number of forces can be replaced by a single force it is known as the…

Q: The truss is shown. Indicate direction to your final answer.   a.) What is the vertical reaction…

A:

Q: Problem 7: Determine the reactions at C and the force in member AB. Ans. FAB = 864 N, C, = 2.66 kN,…

A: Dear student,                     According to the guidelines, I am allowed to answer only one…

Q: The force F1-5 KN, F2-5 KN, F3-10 kN, F4-5 kN are acting on the structure shown. Determine the…

A: According to the given dataTo find-The forces in the members BC , BE and EF

Q: 2. A truss is shown in the figure below. a) Based on the number of joints and members, discuss about…

A:

Q: F₁ F₂- F₂ A B с F3 -F3 D E F

A: Given Data:Applied forces: F1 (unknown), F2 = 11 kN, F3 = 9 kN, F4 = 6 kNDiameter at section B (dB)…

Q: If the roller at B can withstand a max load of 3 kN, determine the largest magnitude, F, of the…

A: Given: max load at roller B = 3kN now we can evaluate force F by using simple equilibrium…

Q: at is the internal normal force?

A: In a beam,  The sum of all the axial force acting at a section of a beam is called as internal…

Q: A rigid beam of negligible weight is supported by a hinge at A and a rocker at B as shown in the…

A: Given:F=16 KN

Q: A 1.5 m B P₁ C -1.5 m 1.5 m- D F P₂ -1.5 m 2 m

A:

Q: Solve the problem shown below. Each answer is worth equal credit. Show all necessary steps of your…

A: The value of applied force is

Q: TRUSS PROBLEM Determine: a) The magnitude and direction of the reactions at 3 and 5 b) The forces…

A: To find - a) The magnitude and direction of the reactions at 3 and 5. b) The forces in each member…

Q: A) Mark each of the zero-force members in the truss with an X. Answer -3 ft F 500 lb 3 ft- E B -3…

A: (A) To find: The zero force member in the truss with an X. FBD: The free body diagram is,

Q: For the following reinforcement, determine the reactions at the supports and the forces in the…

A: For the following reinforcement, determine the reactions at the supports and the forces in the…

Q: Q4) Structural Analysis This bridge is made of two-force members attached at the ends. All angles…

A:

Q: a. What is the tension in the chain? b. What is the magnitude of the force exerted by the hinge on…

A: To determine the tension in the chain and magnitude of the force exerted by the hinge and given the…

Q: 4) Use the method of sections to find the true magnitude and direction of the force in member AB of…

A:

Q: Determine the force in each member of the  truss, and state if the member is in tension or…

A: For the solution refer below images.

Q: Reaction at A: RA = Reaction at B: RB: = kN KN

A:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.