Q4) The dumbell shaped specimen is made from steel rod and is cylindrical in shape, knowing that its value for elasticity is 29000 ksi, Analyze the load which produces deflection of 0.005 inches in the specimen (b) indiviual strain at each portion in it 8 in L = 6 in L= 2 in D = 2 in D= 1.5 in D = 2 in L = 2 in

Q4) The dumbell shaped specimen is made from steel rod and is cylindrical in shape, knowing that its value for elasticity is 29000 ksi, Analyze the load which produces deflection of 0.005 inches in the specimen (b) indiviual strain at each portion in it 8 in L = 6 in L= 2 in D = 2 in D= 1.5 in D = 2 in L = 2 in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Sketch the stress-strain curve of the following tension test??? In the tension test of a metal fracture occurs at maximum load. The conditions at fracture were: A = 100 mm and L, = 60 mm, the initial values were: A = 150 mm and L. 40 mm.
1.5-6 The data shown in the table were obtained from a tensile test of a metal specimen with a diameter of 0.500 inch and a gage length (the length over which the elongation is measured) of 2.00 inches. The specimen was not loaded to failure. d. Estimate the value of the proportional limit. e. Use the 0.2% offset method to determine the yield strength. Elongation (in.) Load (kips) 872236 DIN 2.5 3.5 5 7 8 9 10 11.5 12 0 0.0010 0.0014 0.0020 0.0024 0.0036 0.0044 0.0050 0.0060 0.0070 0.0080 0.0120 0.0180
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 30 x 10-3 mm while those at CD decrease 60 x 10-3 mm in the 290-mm-gage length. Using E = 150 GPa, determine the flexural stress at the top fiber. Answer must be in MPa. Given: a = 50 mm, b = 120 mm, and c = 90 mm. gage length A a mm b mml c mm
If the lateral compressive strain in a material is 0.3 x 10-3 and the Poisson ratio is 0.25, then longitudinal strain in the material is ✓ 0.0012 (tensile) 0.0012 (compressive) 7.5 x 10-5 (compressive) 7.5 x 10-5 (tensile)
Calculate the stress from a 0.3498 in. diameter tensile specimen yielding at 4.407 kips 46.0 ksi 30.6 ksi 33.4 ksi 45.9 ksi
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 40 x 10 -3 mm while those at CD decrease 70 x 10 -3 mm in the 220-mm-gage length. Using E = 180 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa. Given: a = 40 mm, b = 130 mm, and c = 80 mm.
The rectangular plate is subjected to the deformation shown by the dashed lines. Determine the followings: 1) the average normal strain along side AB 2) the average normal strain along the diagonal AC 3) the average normal strain along the diagonal BD 4) the shear strain at B 5) the shear strain at D B C 8P mm 2 mm 4 mm 10P mm
A small aluminum alloy [E = 74 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 130 mm. The cross- sectional dimensions of the tee shape are b = 25 mm, d = 38 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 µɛ is measured from a strain gage located at c = 5 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P Strain gage- d В D E 2 H Answer: P= i N
Answer in two decimal places please
A 13 mm diameter tensile specimen has 50 mm gauge length. If the load corresponding to the 0.2% offset is 6800 kg, the yield stress will be nearly 1. 31 kg/mm² 2. 43 kg/mm² 3. 51 kg/mm² 4. 63 kg/mm² X
A cylindrical tensile specimen has an undeformed diameter of 8.6 mm. It is subjected to a tensile load of 100 kN. The elastic modulus (E) is 10 GPa. Poisson's ratio is 0.25. Calculate the change in the diameter (in mm).
During a tension test, measurements for the applied load and the corresponding elongation are taken at frequent intervals. These data points are then used to: a. calculate the stress caused by the applied load at each data point. b. calculate the strain in the specimen induced by the applied load at each data point. c. plot a stress-strain diagram. d. all of the above