Answered: Q4: Determine the maximum deflection…

Q4: Determine the maximum deflection and its location of the simply supported beam shown in the Figure. (E = 200 GPa) and (I= 65.0×106 mm). 2 m 30 kN 15 kN +2m-2.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure shows an aluminum beam OB with rectangular cross section, pinned to the ground at one end and supported by a round steel rod with hooks formed on the ends. A load is applied as shown. Use superposition to determine the vertical deflection at point A. 2 in 6 in. where F-104 lbf -in dia. F -in thick 12 in -A 12 in B The vertical deflection at point A is .0706 × 10-3 in.
The link CE (Diameter D=12mm) and DF (Diameter D=10 mm) are 300 mm 200 mm connected to rigid link ABCD as shown in the figure. The links CE and DF - 450 mm- are made of E=200 GPa steel. B A D Ca a. Find the force at each link (CE and DF) b. Find the deflection at point A. 32 kN 600 mm 750 mm E F
Question: A barrier gate was hit ba a car and deflected as shown in the figure. Treat the barrier boom as a cantilever made of aluminium with E=70 GPa. Determine the force P caused the deflection if : a. The boom's cross section is solid 60 mm 90mm №3 m b. The boom's cross section is hollow with wall thickness of 5mm. boom 0.3 m 0 60 mm 90 mm
Q2: A simply supported beam as shown below. Determine the deflection at C and D. Take E = 210 GN/m? and I = 16 x10% mm*. 120 kN 80 kN -0.6 m- 1.4 m C 3 m
A gymnast with a mass of m = 40 kg is hanging by one hand from the middle of a simply supported beam with a length L = 1.5 m. The beam has a cross-sectional area of A = 4 cm² and a Young's modulus of E = 15 GPa. a. What are the maximum deflection and maximum stress in the beam if it has a circular cross section? b. If it has a square cross section? c. If it has a hollow cross section with a wall thickness t = 0.5 cm? d. Which is the greatest and least and why? L L/2 F Cross Sections - O
Find the deflection at the mid-point BC of the loaded beam as shown in the figure by the double integration method. ( E= 200GPA I=6,87x10^-6 m^4)
The rigid beam ACE is fixed by both sides as shown in figure, if F1 = 300 kN and F2 = 150 kN. Find the reactions Ra and Rb. Take S = 3.5 mm and E=200 (GPa):
es A gear reduction unit uses the countershaft shown in the figure. Gear A receives power from another gear with the transmitted force FA applied at the 20° pressure angle as shown. The power is transmitted through the shaft and delivered through gear B through a transmitted force Fg at the pressure angle shown. For the steel countershaft specified in the table, find the deflection and slope of the shaft at point A. Use superposition with the deflection equations in Table A-9. Assume the bearings constitute simple supports. In the figure below, FA is 310 lbf and the diameter of the shaft (dshaft) is 1.29 in. dshaft Gear A 20-in dia. 16 in FA 20⁰ The deflection at point A is The slope at point A is 14 in 100 Gear B 8-in dia. rad. 9 in in. B FB 20°
The beam shown in the figure consists of a W360 x 79 structural steel wide-flange shape [E = 200 GPa; I = 225 × 106 mm¹]. For the loading shown, determine: (a) the reactions at A, B, and C. Enter a positive value for a reaction force that acts upward on the beam, or a negative value for a reaction force that acts downward. (b) the magnitude of the maximum bending stress in the beam. Enter a positive value for the magnitude. Note: Use the tabulated value for the section modulus S from Appendix B directly in the stress calculation. Although S is related to the area moment of inertia I and the cross-section depth d, due to round-off in the tabulated data for S, I, and d, a slightly different answer for the bending stress is obtained using S directly as compared to the result obtained in using I and d. Of course, performing the calculation using either S directly, or using I and d, the answer will likely be within the required tolerance. Assume L₁ = 3.2 m, L₂ = 5.3 m, M = 200 kN-m, and w =…