Q4: An inclined circular gate (AB) with hinge support at (B) and the weight of gate (12KN). Determine (FA). (Answer with sketch, See Fig.4) 1.5m 60 1.25m Fig.4

Q: Identify the zero-force member in the truss shown 600 N (a) CD (b) ВЕ (c) вс 2 m (d) CE 900 N E 2 m…

A: In the truss if at a joint only two members are joined and there is no external force at the joint…

Q: AT

A:

Q: If the gap between C and the rigid wall at D is initially 0.15 mm, determine the magnitudes of the…

A:

Q: Design a one-way slab to carry a service live load of 5.5 kPa. The slab has a length of 5 meters…

A: laoding on slab is given. Span and grade of steel and concrete is also given. We need to find out…

Q: D 3kN 1.5 m C В Fig.Q1 2 m 2 m 4 kN

A: Free body diagram and reactions -  Due to symmetry of the forcesRASinθ = RC = 42 = 2KNHA = HC = 32…

Q: Tianged racket is subject couple design of the attachment at A must be determined. Replace the two…

A: Replace the two forces and couple by an equivalent couple M and resultant Rat A. The couple is…

Q: 1. In the structure below, members BF and AE are connected with a pin at D. Find the minimum…

A:

Q: Water In fig find the force on the gate ? h=1.5 m, the gate is square = 2 m B Center of pressure Y α…

A:

Q: In the loaded truss figure shown, F1=16.9kN and F2=17kN. Find the forces carried by the members CF…

A: The FBD of the truss is shown below: Taking equilibrium equations:…

Q: For the reinforcement shown, whose inclined force of 40 kN is applied in the same line of action of…

A: (a) Zero Force Elements: At a unloaded joint, when there are three elements meet out of which two…

Q: Determine the shear at point A for the beam shown. 40 k 40 k Hinge B -10n 10n나-1on- Select the…

A:

Q: 3-78 For a gate width of 2 m into the paper (Fig Answer: 17.8 kN SG= SG=

A:

Q: The frame is subjected to a load of 5 kN which acts on member ABD at D. Determine the required…

A: Given : Load = 5 kN Failure shear stress = 50 MPa FOS = 1.5 Determine the required dia. of pin D…

Q: Find each Reaction. Show a correct FBD.

A:

Q: Problem 2 A 1.0X102 N force in the j direction is applied to piping (ABCDEFG). The points in Fig 2…

A: Given data:- Force F =100 N The force vector is F⇀=(100 i+0 j+0 k) N The coordinates of points;…

Q: EDetermine all forces acting on body A Fort A for the System shown in Fignreca). Body A weighs(200N…

A:

Q: Determine the resultant internal loading acting on the cross sectional at G of the beam shown in the…

A:

Q: he to The structure loaded as shuwn : he 4m P 40 KN E 200 GPa 12=1c_100 x 10° mm • Solve the…

A:

Q: 5.0 The truss figure shown is pinned to the wall at point F, and supported by a roller at point C.…

A: Load act at point A= 80 kNLoad act at point B= 60 kN

Q: is hinged as

A: h = 3m W= 2m theta = 60° we need to find the force  RT to hold the gate in position

Q: Analyze the structure below using cantilever beam method 25KN C 3m 50KN B 4m A F 6m- 8m SOLVE for…

A: Given data in question  Framed structure  Horizontal point loads Cantilever beam method To find out…

Q: Find the support and bond forces

A:

Q: n, determine the maximum value o (a) in link AB, (b) in link BC.

A:

Q: member. (a) Dctermine the coordinates yR and Za of the point where the tensile load P must act in…

A: Please find the answer in the below attachments

Q: 350 기 mm 2400mm 400mm C A B 200mm 8 notice not hinge E 3 D =1 200kg

A: To Determine Reactions at pin C and D on member CDE where E is a roller and A is a pin

Q: Activity 2. Using method of sections, solve for the force acting on member BD of the truss shown.…

A: Activity 2-

Q: Determine the member force on member FI

A: Determination of force in member FI###

Q: (47 H.WOA vod Consists of three bars of unequal dlameters as shown in fig., find the Stress in each…

A:

Q: Determine the reactions at Pin A, Rocker B and Pin C Note that piece ACF and BCDE are each one…

A:

Q: Replace the forces acting on the plate by a wrench. Specify the force and couple moment for the…

A: Consider the figure,

Q: Determine the forces in members CD and CF.

A:

Q: For the truss shown, determine the forces in members (a) BD; and (b) BF. -4 m--4 m-4 m 4 m→ A -4 m→-…

A: This question is solved with the help of the method of sections and the method of joints. Consider…

Q: ! Required information Each of the four vertical links has an 8 x 36-mm uniform rectangular cross…

A: Given data - Cross section = 8×36 mm Diameter of Pin = 16 mm P = 23 KN Find out - Average shear…

Q: a connections, calculate the pin rea . Usea pin diameter of 16 mm in a

A: