Q3/A) Is the response for the following system is under damping? If yes, determine the maximum over shoot, peak time, rise time, and settling time. C(s) = 200 S3+25S2 +250S And the input to the system is unit step.

Q: An opposed louvre type damper is used to regulate air flow to a furnace in order to control the…

A: a) The PLC will read 5.778 mA as a feed back when the louvres are at 10 ∘ b) 12 mA is required to…

Q: P.15.10 A control valve is used to control the flow of water to a cooling coil. The characteristic…

A: Given, maximum flow rate is 150 gpm.At normal conditions, Fraction of maximum flow is given byThus,…

Q: Derive Laplace transforms of the input signals shown in Figs. by summing component functions

A:

Q: What is the difference between an operating line and an equilibrium curve?

A: The operating line and equilibrium curve are to be differentiated.

Q: To ensure turbulent conditions and minimum mixing time during agitation with a turbine impeller, the…

A:

Q: 2. Use Routh Array to check the stability of the process. 92 91 hm LT#LCH Toy Figure 11.22…

A: The Routh stability criterion generally asserts that if and only if every first-column element in…

Q: A CSTR is to operated for 30 minutes with multiple flowrates of one of the input streams. If the…

A: Given data: A CSTR is operated for 30 minutes with multiple flow rates. The flow rate is changing…

Q: 4.8 A surge tank in Fig. E4.8 is designed with a slotted weir so that the outflow rate, w, is…

A: Apply material balance on the given system as:

Q: Determine values for A and R from the step response

A:

Q: Consider the two 8-point QAM signal constellations shown in Figure P3.6. The distance between…

A:

Q: Usually, the steam pressure in a boiler is controlled through the use of a pressure control loop on…

A: Step 1: In boiler systems, maintaining optimal performance involves managing multiple crucial…

Q: Reactor coolant system (RCS) hot leg temperature is 568 deg F and RCS pressure is decreasing due to…

A: To find:The pressure range includes the pressure at which two-phase flow will first occur in the hot…

Q: for question C, why is the dot at when the atm is 1 rather than 0.0001?

A: Phase diagram of a compound is given.

Q: Example 10. Fit the tank in series model to the following mixing cup output data to a pulse input. t…

A:

Q: A surge tank in Fig. is designed with a slotted weirso that the outflow rate w is related to the…

A:

Q: For each of the following controls, state the disadvantage: a)      Derivative control b)…

A: (a) Derivative Control:Disadvantage: Sensitivity to NoiseDerivative control amplifies high-frequency…

Q: Find the frequency response of a first-order system, withG(s)=1/(?s+1)

A: To obtain the frequency response few steps needs to be followed. Here, G(s) is the open loop…

Q: Using frequency response arguments, discuss howwell e^−θ scan be approximated by a two-term Taylor…

A: The exponential term is first approximated by truncating its Tylor expansion to two terms as:

Q: A step change of magnitude 4 is introduced into a system having the transfer.   (c) overshoot ?…

A: Process control is the control of the process variables to get the desired output. On controlling…

Q: A pressure difference of 2.40 x 10 Pa is used to inject a sample onto a 64.2 cm long capillary that…

A: It is given that,pressure difference, ,length of capillary, ,diameter, viscosity of the sample,

Q: Q4: For the signal flow graph of a certain control system shown below, find the system…

A: Step 1:Step 2:

Q: Create an RC circuit (DC supply 10V) that has a RC time constant equal to conds. Pick the resistor…

A: Problem 7: An RC circuit with an input voltage of 10V and time constant of 3.3sec is created using…