Q3/A) In Figure No. (4) the value of pressure of Confined Water pB at the center of pipe No. (2) is 5 (Bar). Find the value of pressure of Compressed Air pa at the center of pipe No.(1). {Note/ yw = 9.81 (KN/m³), GĦg = 13.6}. BPipe No.(2) water comressed Air Pipe No (1) 4.5m water 1.2m Air 2.7m (2) (1) Fig.(4) Mercury

Q3/A) In Figure No. (4) the value of pressure of Confined Water pB at the center of pipe No. (2) is 5 (Bar). Find the value of pressure of Compressed Air pa at the center of pipe No.(1). {Note/ yw = 9.81 (KN/m³), GĦg = 13.6}. BPipe No.(2) water comressed Air Pipe No (1) 4.5m water 1.2m Air 2.7m (2) (1) Fig.(4) Mercury

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Water flows with a discharge of 0,02 through a SG pipe reducer as is shown in the Figure 1. The…

A: Given Q=2D1=3mD2=1mGoil=S.G=0.7

Q: The velocity of water flowing through a 30mm pipe is 2 m/s. The fluid has a dynamic viscosity of 100…

A: Data is as given

Q: Probl Compute gage pressure at the center of pipe. For solution use: (a)British Unit, (b)Standard…

A: To Determine Gauge pressure in the centre of the pipe. a) In British unit ( psi ) b) In SI unit (…

Q: Pipe 1 is 450mm dia. and 1800m long, Pipe 2 is 300mm dia. and 1500m long, and Pipe 3 is 250mm dia.…

Q: Determine the friction factor f if ethyl alcohol at 25°C is flowing at 5.3 m/s in a standard DN 40…

Q: A fire protection system is supplied from a water tower and standpipe 80ft tall. The longest pipe in…

A: Given that :

Q: For the piping system of Fig. all pipes are concrete with a rough of 0.04 inch. Neglecting minor los…

Q: Water flows from a pressurized tank, through a valve and out a pipe. If Q = 0.1 ft/s, Az = 10 ft,…

A: given- a pressurised tank having a pipe attached to it. to find- the pressure in pressurised tank.

Q: The pipe network shown in the figure represents a sprav rinse system Find the flow in each pipe…

Q: The horizontal wye fitting, as shown below, splits Ql into two equal flow rates. At section 1, Q1 =…

A: Discharge is the main quantity in any field used to transfer fluids from one place to another in the…

Q: A fluid of specific gravity 0.8 and dynamic viscosity 15 x 10-Pa s is flowing in a 15mm diameter…

A: Given that specific gravity of fluid is 0.8 Dynamic viscosity of fluid is 15×10-4Pa.s Diameter of…

Q: horizontal pipe is diverted upwards with an angle of 25 degrees. Water enters with a velocity of 4.5…

Q: Consider the section of water distribution piping shown below. Ignoring minor losses, find the flow…

A: From the above figure the given values are as follows,EA=141mZA=60mA-B:-3000m@400mmC=120…

Q: The water is flowing through a P, 39.24 N/cm D, 20 cm Problem 6.4 pipe having diameters 20 cm and 10…

Q: Q1) Given is a three-pipe series system, as in Fig. 150,000 Pa, and the elevation drop is ZA - ZB…

A: The pressure drop is PA - PB = 150000 Pa zA - zB = 5 ρ = 1000 kg/m3 ν = 1.02 × 10-6 m2/sec

Q: 7-40. SAE 30 oil at 68°F flows through the piping system shown in Figure 7.38. (a) If Q₂ = 20 gpm,…

Q: A cylindrical tank with vertical axis contains water. A 50 mm orifice is located at the side 0.60 m…

A: Given: Diameter of the top orifice = 75mm, Diameter of the lower orifice = 50mm, Both orifices have…

Q: A pipe connected in series has the following roughness or friction coefficients: Pipe 1 C = 90…

Q: Air flows at the rate of 1.5 m3/s through a horizontal pipe with a gradually reducing cross-section…

Q: a) With the aid of a diagram, differentiate between pipe in series and pipe in parallel in term of…

A: As per our company guidelines, we are supposed to answer only one question. Kindly repost other…

Q: Q3)Air flows steadily through a horizontal 4-in.-diameter pipe and exits into the atmosphere through…

A: consider point 1 at 4 in diameter section and point 2 at exit Pipe is horizontalpreesure at 1 p1…

Q: Current Attempt in Progress (Bernoulli/continuity) Water flows steadily through the pipe shown in…

A: GIVEN- Pressure at section 1(P1)=320 kPa Pressure at section 2(P2)=80 kPa Velocity at section 1…

Q: 7. Given the following total heads H1= 8 ft and H2-106 ft and Q= 10cfs, calculate the head needed to…

A: As per bartleby policy i can answer only one question at a time. Please upload again other…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

Q3/A) In Figure No. (4) the value of pressure of Confined Water pB at the center
of pipe No. (2) is 5 (Bar). Find the value of pressure of Compressed Air pa at the
center of pipe No.(1). {Note/ yw = 9.81 (KN/m'), Gg = 13.6}.
BPipe No.(2)
water
comressed
Air
Pipe No (1)
4.5m
water
1.2m
Air
2.7m
(2)
(1)
Fig.(4)
Mercury

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1given

VIEW

Step 2 calculation

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

MY REGISTRATION NO IS 5350
nat7
Q/In Figure No. (4) the value of pressure of compressed air pa in pipe No.(1) is 3.8 (Bar). Find the value of pressure of water pg in pipe No. (2). B Pipe No.(2) water comressed Air Pipe No.(1) 4.5m water xA 2.7m 1.2m Air (2) (1) Fig.(4) Mercury
سمنب Fluid mechanics
3. A 30m long, 20mm diameter steel pipe is used to drain an oil tank determine the discharge 3E when the oil level in the tank is 4m above the exit of the pipe. Neglect minor losses, (assume f = 0.12) 4m D-20 mm, L-30 m, t 0.12
Plz, solve this problem as detail as clear. Reg.no: 5395 Fluid Mechanics-2
7-40. SAE 30 oil at 68°F flows through the piping system shown in Figure 7.38. (a) If Q₂ = 20 gpm, what is the largest allowable value of 2; so that the flow in inlet pipe 1 is laminar? (b) For the calculated value of Q₁, determine whether the flow is laminar or turbulent in pipes 2 and 3. Globe valve 1 in. dia. 1.25 in. dia. 1.25 in. dia. Pipe 4 21 Pipe 1 f Pipe 2 Pipe 3 Globe valve 3/4 in. dia. Figure 7.38 System for Exercises 7-40 and 7-41. 24
Someone can help me with this one please.
3)a: For the figure below, find the discharge in pipe, neglect the minor losses only. (e-0.001m, D-Im, L-600m, u-1.307*10 m/sec). LAS 5m 2 1.96 D. b: In a pipe of 300 mm diameter the maximum velocity of the flow is found to be 2 m/s. If the flow in the pipe is laminar, determine: 1) The average velocity and the radius at which having the same velocity magnitude as the average velocity. 2) The velocity at 50 mm from the wall of the pipe. 5964 11.62
A cylindrical tank with vertical axis contains water. A 50 mm orifice is located at the side 0.60 m above the bottom of the tank and 1.50 m directly above the orifice is another orifice 75mm diameter. Cv is 0.98 and C is 0.61 for both orifices. Determine the: show complete solution thumbs up guaranteeda. h1 in metersb. Discharge in the lower orifice in lit/secc. Total discharge from the 2 orifices in lit/sec
Problem #12 Water 16 in diameter -diameter nozzle Determine the discharge in the pipe (in cfs) and the pressure at point B (in lbf/sqft). Neglect head losses. Assume a = 1.0 at all locations.
Determine the pressure at point C in psi. Determine the pressure at point D in psi. Determine the flow rate in cfs. Determine the velocity at the pipe with 18 inches diameter in ft/s.