Q3/A flat bet is required to transmit 30 kW from a pulley of 1.5 m effective diameter running at 300 r.p.m.The angle of contact is spread over (I1/24) of the circumference. The coefficient of friction between the belt andpulley surface is 0.3. Determine, taking centrifugal tension into account, width of the belt required. It is giventhat the belt thickness is 9.5 mm, density of its material is 1100 kg / m and the related permissible workingstress is 2.5 MPa

Q3/A flat belt is required to transmit 30 kW from a pulley of 1.5 m effective diameter running at 300 r.p.m. The angle of contact is spread over (11/24) of the circumference. The coefficient of friction between the belt and puliey surface is 0.3. Determine, taking centrifugal tension into account, width of the belt required. It is given that the belt thickness is 9.5 mm, densiry of its material is 1100 kg / m and the related permissible working stress is 2.5 MPa

Q3/A flat belt is required to transmit 30 kW from a pulley of 1.5 m effective diameter running at 300 r.p.m. The angle of contact is spread over (11/24) of the circumference. The coefficient of friction between the belt and puliey surface is 0.3. Determine, taking centrifugal tension into account, width of the belt required. It is given that the belt thickness is 9.5 mm, densiry of its material is 1100 kg / m and the related permissible working stress is 2.5 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

QUESTION 1 Determine the maximum force P that can be applied without causing movement of the 250 lb homogeneous block. The coefficient of static friction between the block and the floor is 0.4 and between the 4 ft diameter wheel and the rope is 0.2. 커 3 ft 4 ft
If the clamping force at G is 900 N, determine the horizontal force F that must be applied perpendicular to the handle of the lever at E. The mean diameter and lead of both single square-threaded screws at C and D are 25 mm and 5 mm, respectively. The coefficient of static friction is μ = 0.3. Answer: F = 66.7N 200 mm- -200 mm OA C 125 mm
View Policies Current Attempt in Progress The 669-N force is applied to the 112-kg block, which is stationary before the force is applied. Determine the magnitude and direction of the friction force Fexerted by the horizontal surface on the block. The force is positive if to the right, negative if to the left. H₂ = 0.72 HA=0.48 Answer: F= Save for Later i 40" N P = 669 N Attempts: 0 of 1 used Submit Answer
A 30m steel tape was standardised at temperature of 20ºc and under a pull of 5kg. The tape was used in catenaryat a temperature of 25ºc and under a pull of 11kg. The cross sectional area of the tape is 0.02cm2, its weight perunit length is 22g/m. Young’s modulus= 2x10-6 kg/cm2, α=11x10-6 per ºC. Find correct horizontal distance.
An IR profile 304.8mm x 12.50 kg / m, (IR 12 '' x 12 '' or H) It is used as a column and receives an eccentric compression load P of P = 120 Ton, determine: Characteristic values, design the plane of efforts and locate your EN
A shunt generator supplies a 23kW load at 220V through cables of resistance, R = 110m2. If the field winding resistance, Rf =520 and the armature resistance, Ra =50mN. Determine the following below: The terminal voltage is, The e.m.f. generated in the armature is,
2. The 50 kg uniform crate initially rests on the inclined surface. If a force (F-40t +200 N) as shown in the figure below starts to pull the crate, determine the power output develop by the force at t-6 s. The coefficients of static and kinetic friction between the crate and the surface are s-0.20 and Hk-0.15. F-40t+200 N F (r in second) 30°
5 m T Į 2.5 m 10 kN B A с D 10 m For the portal frame shown in the above figure, the final end moments are: 'AB' - 15 kN.m, MBA=10 kN.m, McD = 20 kN.m, The end moment at Moc will be CD DC