Q30: The pin B supports the Load W= 9000 lb and connects horizontal cable with point A. If the pin C is subjected to double shear while pin at B is a single shear. The diameter of pin C is 1.5 in while the diameter of pin B is 0.8 in. Determine the shear stress at pins B and C. Also find the stress in the cable AB if its diameter is 0.5 in.

Q30: The pin B supports the Load W= 9000 lb and connects horizontal cable with point A. If the pin C is subjected to double shear while pin at B is a single shear. The diameter of pin C is 1.5 in while the diameter of pin B is 0.8 in. Determine the shear stress at pins B and C. Also find the stress in the cable AB if its diameter is 0.5 in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Q16/ The value of the normal stress due to :axial force 2 kN applied on the beam is Point D 10 kN…

A: For this question, Axial force = P = 2 kN = 2000 N Cross section of the beam = 200 mm x 100 mm We…

Q: The control arm is subjected to the forces as shown in Figure 3.5 – 7. All dimensions are in mm. TA…

Q: The rectangular bar is connected to the support bracket with a 12-mm-diameter pin. The bar width is…

Q: The cylinder of a hydraulic ram supported at the open end is 200 mm internal diameter and is…

Q: Q4(): The pin D has a diameter of 0.75 inch and subjected to single shear. The pin at B is subjected…

Q: The pin-connected frame supports the loads P1 = 5 kN and P2 = 10 kN. Determine for an angle of α =…

Q: The solid circular rod has a cross-sectional area of 470 mm². It is subjected to a uniform axial…

Q: 10/.. find the shear stress in bolts 4 80 kN 80 kN -O- O--O- 300 mm

A: Write the expression for the load acting on the riveted joint.

Q: The bell crank is in equilibrium for the forces acting in rods (1) and (2). The bell crank is…

A: The given information in the problem is shown in the following attached image:

Q: 1- Find the shear stresses at A and B points when the force V applied to the beam is 20 kN. 200 mm…

A: Given, The width of the I-section, b=125 mm The height of the I-section, h=250+30+30=310 mm The…

Q: A lever is attached to a shaft with a square shear key as shown. If the force applied to the lever…

A: Solution - Given data - P= 385 N

Q: A lever is attached to a shaft with a square shear key as shown. If the force applied to the lever…

A: GivenP=375N

Q: The shear stress is maximum on the principal plane Select one: True O False

Q: d2 mm 60 mm FAN dlmm 10 mm 40 mm The shaft shown is subjected to the axial force(F) of 30 kN. If the…

Q: Problem No. 3. The compound shaft has the following properties: G in both Segment 1 Segment 1 pipe…

Q: Use the graphical method to construct the shear-force diagram and identify the magnitude of the…

A: To Find : The shear force diagram and magnitude of maximum shear force.Given : The moment at the…

Q: Two fully loaded tractor trailers travel over the bridge putting substantial loading on the…

A: The objective of this question is to calculate the shear strain at point T when a vertical…

Q: For the connection shown, the bolt diameter is d = 30 mm. The average shear stress in the bolts…

Q: 1) Two wrenches are used to tighten the pipe. If P = 300 N is applied to each wrench, determine the…

A: The value of shear stress in the segment AB can be expressed as shown below.…

Q: Q1/ The channel section shown below is simply 30 mm 30 mm supported over a span of 5 m and carries a…

A: Given: The length of the section, L = 5 m The intensity of udl, w = 15 kN/m

Q: 30 -1.5m A D 80KN 5m 80KN 1.5m 40μN

Q: ● ● ● the rigid bar AB is on a smooth incline the 5/8 diameter pin at B is in double shear Determine…

A: Given:Force acting on th ebeam, F=2000 lbDiameter of the pin, d=58 in

Q: mine the stre t B. Then dr

Q: QI/ The 15-mm diameter steel bolt is screwed tightly into a block at A. Suppose that the couple…

A: Write the length of the wrench. L=300 mm=300 mm×1 m1000 mm=0.30 m Write the displacement of the…

Q: The shears shown are exerting a vertical force on the branch at point E. Find the load in 2-force…

Q: The wide-flange beam is subjected to the 50-kN force. Determine the principal stresses in the beam…

Q: Q120: Determine the stress in cable shown in the figure if its diameter is 10mm. If the pins at A…

A: Consider the free body diagram as shown below for the given system.

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

Q30: The pin B supports the
Load W= 9000 lb and connects
horizontal cable with point A. If
the pin C is subjected to double
shear while pin at B is a single
shear. The diameter of pin C is
1.5 in while the diameter of pin
B is 0.8 in. Determine the shear
stress at pins B and C. Also find
the stress in the cable AB if its
diameter is 0.5 in.
6 ft
W
9 ft

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step by step

Solved in 7 steps with 9 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The bell-crank mechanism is in equilibrium for an applied load of F₁ = 18 kN applied at A. Assume a = 270mm, b = 150mm, c = 70mm, and 0= 50°. Pin B is in a double-shear connection and has a diameter of 33 mm. The bell crank has a thickness of 39 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Support bracket F₁ Answers: Ob Tpin B = Bell crank Bu CI B MPa MPa F₂
NEED ASAP THANK YOU
The rectangular bar is connected to the support bracket with a 19-mm-diameter pin. The bar width is w = 70 mm and the bar thickness is 15 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 135 MPa, the bearing stress in the bar cannot exceed 150 MPa, and the bearing stress in the bracket cannot exceed 130 MPa. Determine the maximum value of Pmax that can be supported by the structure. P Answer: Pmax i kN
Use the graphical method to construct the shear-force diagram and identify the magnitude of the largest shear force (consider both positive and negative). The ground reactions at the wall of the cantilever are provided. L₁= 14.75 ft L₂ = 7.75 ft Vc = 91.50 kips Mc = 706.4375 kip-ft 20 kips 6 kips/ft L₁ 103.50 kips 68.50 kips 91.50 kips O 79.50 kips O 114.50 kips 70 kips BO 12 kips/ft L2 O Vc Mc
Q70: For the truss shown in the Figure, if the diameter of pins at A and E are 60mm and 80mm, respectively. The stress in A is double shear while it is single shear in E. Determine the shear 3m 2m 2m 3 m 3 m 3 m F 3 m 110KN 110 KN stresses in pins at A and E and the stresses in members BG; and member BC if their diameter is 110 mm.
Q1/ Find the value of P for the joint shown in the figure if the allowable shear stress is 100 MPa for the rivets. The four rivets are equal, each of 20 mm diameter. | 100 100 200 600 All dimensions in mm.
All the pins are in double shear, and they each have a diameter of 14 mm. The average shear stress in each pin CANNOT exceed 70 MPa. What is the max magnitude of P that the beam can support
If the pin at C has a diameter of 5 mm and is subjected to double shear, the maximum average shear stress, in MPa, is P B