Q3. The system shown consists of 800 m long pipe of 5 cm cast-iron pipe connected into 400m long pipe of 7 cm Riveted Steel pipe, two 45° (k-0.2) and four 90° (k-0.3) flanged long-radius elbows, a fully open flanged globe valve (k-8.5), and a sharp exit into a reservoir. If the elevation at point (1) is 400 m, what gage pressure is required at point (1) to deliver 0.005 m³/s of water at 20°C into the reservoir? 7cm diameter Riveted Steel pipe, 400m-Long Elevation 500m Open Sharp ext Son diameter cast Iron pipe 800m-long

Q3. The system shown consists of 800 m long pipe of 5 cm cast-iron pipe connected into 400m long pipe of 7 cm Riveted Steel pipe, two 45° (k-0.2) and four 90° (k-0.3) flanged long-radius elbows, a fully open flanged globe valve (k-8.5), and a sharp exit into a reservoir. If the elevation at point (1) is 400 m, what gage pressure is required at point (1) to deliver 0.005 m³/s of water at 20°C into the reservoir? 7cm diameter Riveted Steel pipe, 400m-Long Elevation 500m Open Sharp ext Son diameter cast Iron pipe 800m-long

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 40m 120 1.2L/ Water ervoirs A and B are connected to each other through a 40-m-long, 2-cm swing…

Q: Discussion: 1. Designa hydraulic circuit to operate the shear as in part B as well as ersuring that…

A: A shuttle valve, also known as a double-check valve, allows pressure in a line to be obtained from…

Q: Q3/ Three opening of head regulator with 2 m each. The head between US and DS equals to 1.75 m. and…

A: 3 head regulator with 2m each head h= 1.75 mvertical opening = 2.5 mCd = 0.62need to find1- the…

Q: Water is flowing at the rate of 300 L/sec from A to E as shown. Assume f = 0.025 for all pipes.…

A: Q=300L/s To find Q2

Q: A 1 m diameter new cast iron pipe 800 m long and has a head loss of 1.11 m Find the discharge in…

Q: A centrifugal pump having outer diameter equal to two times the inner diameter and running at…

A: Given : Outer dia = 2 inner dia Running at 1200 rpm total head of 32 m velocity of flow = 3m/s outer…

Q: A 6-in-diameter pipe (reentrant entrance, f = 0.028) 475+(Reg.No/100) ft long can deliver water from…

Q: --1. For supplying water to a colony, it is intended to store water in a Targe tank, whose water…

Q: a. For horizontal system, if (P1-P2-800kPa), velocity for pipe A -2.5m/sec, coefficient of friction…

Q: (Single pipe with pump) The pump shown in the figure below adds a 13-ft head to the water being…

A: Introduction- A pump is a machine that transports liquid (liquids or gases). Pump are divided into…

Q: A fire pump delivers water through 15 cm main pipe to a hydrant to which is connected an 8 cm hose,…

Q: determine the pump brake power if the pump efficiency is 82%.

Q: Q-4: A flow net for flow around a single row of sheet piles in a permeable soil layer is shown in…

A: Piezometers measure pore water pressure (piezometric level) in the ground using geotechnical…

Q: For the opened channel find the discharge if (S= 1/200) and (n=0.015).

Q: A sprinkler with unequal arms issuing jets of area 0.8 cm² at each end and facing same direction…

Q: A pump is delivering water at atmospheric pressure to an elevation of 400 m. Elevation of the pump…

Q: Two reservoirs A and B is connected by a 250mm-dia. pipe which is 1000m long. Reservoir B is 8…

A: Given;QEF = 27 litre/secfriction factor (f) = 0.022 for all pipes.

Q: Water flows freely from the reservoir shown through a 50-mm diameter pipe at the rate of 6.66…

A: Fo find out the elevation in meter of the water surface in the reservoir. Given data, Q = 6.66 L…

Q: QUESTION 1 2,=? @ Sharp Edged Entrance K-0.5 Stahdard elbow, threaded D-30 mm 2,-4m System boundary…

A: Solution: Given Data: d=50 mm Volumetric flow rate (Q) =0.006 m3/s KL value for standard elbow…

Q: A 300mm x 300mm pipe discharges 600 L/s of water where the length is 30m. Determine the head loss if…

Q: eries pipe ABCD consists of 6100 m of 400-mm, 3050 m of 300-mm, and 1520 m of 200-mm C=100). Find…

Q: SITUATION 9: Medium oil having a sp. gr. of 0.90 flows through a 120 mm diameter pipe with a mean…

A: Diameter of pipe, d = 120mmMean velocity, Vav = 5.3m/secThe specific gravity of the soil, G =…

Q: The total head loss from A to E as shown in the figure is 20 meters. Use friction factor, f = 0.02…

Q: 4.2.11. A pump is needed to convey 8 cfs of water at 68°F through a 130-ft-long horizontal, ductile…

A: Detailed explanation:Final values might differ a little bit due to calculation done by…

Q: A 30m long, 20mm diameter steel pipe is used to drain an oil tank determine the discharge when the…

Q: A 1 m diameter new cast iron pipe 800 m long and has a head loss of 1.11m. Find the discharge in…

Q: Main Pipe :35 m, 90 deg bent Community B Community A 30 m 25 m Pump Pump ym 10 m 10 m Fig .2:…

A: Given, Discharge(Q) = 45m3/s Velocity(V) = 1.235 m/s Area(A) = Q/V = 45/1.235…

Q: Three pipes, Pipe A of 300 m and 30 cm diameter followed by Pipe B of 150 m and 20 cm diameter…

A: The difference in the elevation of the two reservoirs, h = 10m Pipe Length, m Diameter, cm…

Q: Q4: The pump is adding 7500W fluid power to the flow (toward J) in fig.(2). Find the flow in each…

Q: Water is flowing at the rate of 300 L/sec from A to E as shown. Assume f = 0.025 for all pipes.…

Q: water is flowing through a 35cm diameter welded steel pipe (f=0.014) of length 2300m that drains a…

Q: ntet pump 20 NP SH A. ? static discharge Head static suction head

Q: (67) The water tank shown is filled by pumping water from the well where the water level is located…

Q: Operating point of a pump is obtained through the intersections between the system curve line with…

A: Given, Pump system consisting of two reservoirs

Concept explainers

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.

Question

Q3. The system shown consists of 800 m long pipe of 5 cm cast-iron pipe connected into 400m
long pipe of 7 cm Riveted Steel pipe, two 45° (k-0.2) and four 90° (k-0.3) flanged long-radius
elbows, a fully open flanged globe valve (k-8.5), and a sharp exit into a reservoir. If the
elevation at point (1) is 400 m, what gage pressure is required at point (1) to deliver 0.005 m³/s
of water at 20°C into the reservoir?
7cm diameter Riveted Steel
pipe, 400m-Long
Elevation
500 m
V
Open
globe
Sharp
ext
45 5cm diameter cast Iron pipe
800m-long

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given

VIEW

Step 2: Calculation of total head losses in cast iron steel pipe

VIEW

Step 3: Calculation of total head losses in riveted steel steel pipe

VIEW

Step 4: Calculate gauge pressure at point 1

VIEW

Solution

VIEW

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

أنت الآن Q-2 Water flows through a vertical contraction (venturi) section. Piezometers are attached to the upstream pipe and minimum area section as shown. The velocity in the pipe is 3 mis. The difference in elevation between the two water levels in the piezometers is 15 cm. What is the velocity at the minimum 15 cm area? 3 mis II
Q1: Find the discharge through the pipe if The diameters of sections (1) and (2) are 25 cm and 30 cm respectively. The velocity of water at section (1) is 6 m/s. Determine also the velocity at section (2) D- 3ecm D25 cm 6m/s
Q1) Find The magnitude and direction of The Rorce exerted on The Blade shown bulowby aget, iE The slope angle (0= 120),The velocity V=Vz= 30m/sec, and The discharge (loLIsec)? Blade des Fx Fy
he 30o directional pressure pipe elbow in the vertical plane is 60 cm in diameter. from the elbowThe flow rate of the current passing is 1 m3/s. At the lower end (1) of the elbow, the pressure is 70 kPa and the ground level is 30 m, the upperAt the end of the section (2), the ground level is 31 m. The fluid is water (ρwater=1000 kg/m3), frictionless and incompressible.taking into account thata) Find the velocities in sections (1) and (2) and the pressure in section (2).b) The weight of the pipe at the elbow is 1400 N. In case the length between sections is 1.2 mIn order to keep the elbow stable, taking into account the mass of water in the elbow, in the vertical directionCalculate the force that must be applied.
q4
A flocculator is 16 ft (4.88 m) deep, 40 ft (12.2 m) wide, and 80 ft (24.4 m) long. The flow of the water plant is 13 mgd (20 cfs, 0.566 m³/s). Rotating paddles are supported parallel to four horizontal shafts. The rotating speed is 2 rpm. The centre line of the paddles is 5.5 ft (1.68 m) from the shaft (mid-depth of the basin). Each shaft equipped with six paddles. Each paddle blade is 10 in (25 cm) wide and 38 ft (11.6m) long. Assume the mean velocity of the water is 28 percent of the velocity of the paddles and their drag coefficient is 1.9. Estimate: (a) the difference in velocity between the paddles and water (b) the useful power input (c) the energy consumption per million gallons (Mgal) (d) the detention time (e) the value of G and Gr at 60 °F (f) the loading rate of the flocculator
Q6
Water (p = 1000 kg/m³) flows horizontally through a nozzle into the atmosphere under the conditions given below. (assume steady state flow). Nozzle Water 2 O A2, V₂, P₂ A₁, V₁, P₁ At inlet: A₁ = 10-3m²; V₁ = 2m/sec; P₁ = 3 x 105 Pa (gauge) At outlet: A₁ = 10-4 m²; P2 = Patm Determine the external horizontal force needed to keep the nozzle in place.
Q3/ Three opening of head regulator with 2 m each. The head between US and DS equals to 1.75 m. and the vertical opening of the gates is 2.5 m. if the water in the DS decreases by 0.25 m. Use cd as 0.62 and find the following: a- the vertical gate opening required to maintain the same amount of the discharge if the water level in the D/S decreases by 0.25 m b- the vertical gate opening required to maintain the same amount of the discharge if the water level in the U/S and D/S rise by 0.5 m
Two reservoirs A and B is connected by a 250mm-dia. pipe which is 1000m long. Reservoir B is 8 meters below that of A. Other reservoirs C and D are also connected by a 300mm-dia. pipe, 2,200m long with reservoir D 10mbelow that of C and reservoir C is also 4m below that of A. In order to increase the quantity of water entering reservoir D, thetwo pipelines AB and CD are connected by a pipeline EF which is 1800m long which branches from the 250mm-dia. at a point E 400 meters from A and connects with the 300mm-dia. pipe at F 800 meters from reservoir D.a). Determine the quantity of water flowing towards B and D if 27 liters per second flow through pipe EF. Assume frictionfactor f to be 0.022 for all pipes. Consider only friction losses.b). Determine also the diameter of the pipe EF to carry 27 liters/sec.
answer asap. need the answer within 1 hour. will upvote
A thin 6-ft-wide, right-angle gate with negligible mass is free to pivot about a frictionless hinge at point O, as shown in the figure below. The horizontal portion of the gate covers a 2-ft diameter drain pipe, which contains air at atmospheric pressure. Determine the minimum water depth, h, at which the gate will pivot to allow water to flow into the pipe. Width 6ft- Right-angle gate Hinge 39000 0. 4 ft Water 2ft-diameter pipe