Q3. In Fig. 3 below, the pump move water from tank A to pressurized Tank Bat rate of 100 m³ in 5 min. Perform appropriate calculation to determine if the pump with 2.5 hp works for this purpose. Repeat the calculation and determine if the pump works with air pressure in Tank B of 2.5 atm instead 1.5 atm. P-1.5 atm Preure dow release 4m 50 m 4 m Pump Figure 3 water supply system

Q3. In Fig. 3 below, the pump move water from tank A to pressurized Tank Bat rate of 100 m³ in 5 min. Perform appropriate calculation to determine if the pump with 2.5 hp works for this purpose. Repeat the calculation and determine if the pump works with air pressure in Tank B of 2.5 atm instead 1.5 atm. P-1.5 atm Preure dow release 4m 50 m 4 m Pump Figure 3 water supply system

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Hello! Kindly answer the problem attached image below. Thank you! ASAP
Plz write neat
Determine the shaft horsepower for an 80% efficient pump to discharge 30L/s through the system. The system losses, exclusive of pump losses, are 12V2/2g and H = 16m. Ans: 8.75hp H 150mm dia
The table below gives the pump curve data for a pump operating at 1000 rpm and has 3-in. impeller. The available pumps had different impeller diameter D and rotation speed N as shown below. 1. Draw the pump curve for each pump. 2. What is the discharge provided by each pump when the Head is equal to X? Standard Pump Flow (gpm) Head (ft) 80 500 75 Pump 1 Pump 2 Pump 3 1000 73 N (rpm) D (in) 750 500 600 1500 70 4 6. 2000 67 2500 62 3000 58 3500 52
Example 1: A flow of water from a reservoir to a pipe of different diameters shown in Figure below. Calculate 1) the discharge and velocity at each pipe, 2) the pressure in each pipe and 3) the energy and hydraulic grade lines. water 10m D1-300mm D2-200mm D3=100mm D4-50mm (nozzel)
Fluid Mechanics Provide detailed solutions and drawings. PLS!!! answer the table on the given problem.
Kindly answer the question in all steps
For the setup shown in the figure :
The following data refers to centrifugal pump for pumping water. Static suction head = 5 m; Length of suction pipe = 10 m Static delivery head = 20 m Delivery pipe length = 30 m Discharge = 1500 LPM Perform complete design of pump showing suitable layout.
Part 1 Part 2 Part 3 hp A centrifugal pump having a 7.5-in-diameter impeller and the characteristics shown in the figure below is to be used to pump gasoline through 4000 ft of commercial steel 3-in.-diameter pipe. The pipe connects two reservoirs having open surfaces at the same elevation. Determine the flowrate. Do you think this pump is a good choice? This figure is referred to as the pump performance characteristics. 500 8 in. dia 400 7 出300 6 Head, ft 200 100 65 60 55 50 40 bhp 30 25 20 80 ° 40 120 160 200 240 280 320 Capacity, gal/min Write the system equation for this flow system as function of the friction factor f and volume flowrate Q in gal/min. (Use 2 significant digits on coefficients. Do not enter units as a part of your response.)
A closed tank contains 20 m deep water. A hose is connected as shown such that the nozzle (diameter = 1cm) is directed straight up, If the air gage pressure inside the tank is 20©kPa, solve the actual mass flowrate if the coefficient of discharge through the nozzle is 0.6. AIR 20 m O 1.59kg/s O 1.22kg/s O 1.86kg/s O 1.33kg/s
Q4: The pump shown in figure (2) adds 25 kW to the water and causes a flow rate of 0.04 m³/s. Determine the flow rate expected if the pump is removed from the system. Assume f= 0.016 for both case and neglect minor losses. 40-mm-diameter nozzle (2) 60-mm-diameter, 30-m-long pipe; f = 0.016 Pump T h (1) Fig. (2)