Q3) The screw, as shown is operated by a torque applied to the lower end. The nut is loaded and prevented from turning by guides. Assume friction in the ball bearing to be negligible. The screw is a triple-start trapezoidal thread. The outside diameter of the screw is 48 mm and the pitch is 8 mm. The coefficient of friction of the threads is 0.15. For trapezoidal threads, 2 B=30°) Find: 1. Load which can be raised by a torque of 40 N-m; and 8 WV.C.n W G.d Pb ndin 2. Average bearing pressure between the screw and nut thread surface. T₁ = ² × H, X W (R.) ¹ - (R₂) ² (R₁)²-(R₂)²] 8 (Assuming uniform wear conditions) =H₁*W*R JANNER RANGARaheb Main eginal (Assuming uniform pressure conditions) 197 50 mm

Q3) The screw, as shown is operated by a torque applied to the lower end. The nut is loaded and prevented from turning by guides. Assume friction in the ball bearing to be negligible. The screw is a triple-start trapezoidal thread. The outside diameter of the screw is 48 mm and the pitch is 8 mm. The coefficient of friction of the threads is 0.15. For trapezoidal threads, 2 B=30°) Find: 1. Load which can be raised by a torque of 40 N-m; and 8 WV.C.n W G.d Pb ndin 2. Average bearing pressure between the screw and nut thread surface. T₁ = ² × H, X W (R.) ¹ - (R₂) ² (R₁)²-(R₂)²] 8 (Assuming uniform wear conditions) =H₁WR JANNER RANGARaheb Main eginal (Assuming uniform pressure conditions) 197 50 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Solve the following problem (NOTE: Use any reasonable DATA not given in the problem.)
A basic single-thread, square-threaded screw jack is shown. It is designed to lift a load F that sits atop the collar. The screw turns when a force into the page is applied at end of the handle. For the screw jack threads, the major diameter is 35 mm, the pitch is 6 mm, and the coefficient of friction is 0.085 for the nut and 0.13 for the collar, whose diameter is 44 mm. The design calls for the jack to raise a load of 9.5 kN when 85 N is applied to the lever. collar handle nut Calculate the mean diameter of the threads. Calculate the torque required to overcome collar friction. Calculate the minimum length L needed to raise the load.
The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction between the belt and the 36° V-pulley is 0.15, and the weight of the han- dle is 15 N. If a force of 200 N is aPplied to the end of the handle, determine the maximum torque for which no mo- tion occurs if the torque is applied Counterclockwise. 150 mm T 200 N 60 150 mmi 675 mm 75 mm
(b) In an engine governor of the Porter type, the upper and lower arms having equal length, 200 mm and pivoted on the axis of rotation. The mass of the central load is 15 kg, the mass of each ball is 2 kg and friction of the sleeve together with the resistance of the operating gear is equal to a load of 25 N at the sleeve. If the limiting inclinations of the upper arms to the vertical are 30° and 40°, find, taking friction into account, range of speed of the governor.
2. The clamp of the given figure is used to hold a cover in place. The screw of the clamp has a single thread with a mean radius of 0.20 in and a pitch of 0.08 in. The coefficient of friction is 0.45, and the required clamping force is 100 lb. (a) Determine the twisting moment to tighten the clamp and (b) determine the twisting moment to loosen the clamp.
The roughly position of the automobile jack shown in the figure is a square screw with a single blade at both ends. ABC is controlled by a bolt (right-hand threaded in A, left-handed in C). square of the bolt screw has a pitch of 2.5 mm and an average diameter of 9 mm. between the bolt and the jack limbs The coefficient of static friction is 0.15, taking into account the position and load shown, you can use the jack Find the magnitude of the torque that must be applied to raise it.
The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction between the belt and the 40 V-pulley is 0.10. The weight of the handle is 2 lb. If a force of 50 lb is applied to the end of the han- dle, determine the maximum torque for which no motion occurs if the torque is applied Counterclockwise. 50 Ib 3 in. +9 in- 18 in.-
What is the correct answer?