A self-locking C-clamp is used to hold a workpiece with a clamping force of 5000 lb. The screw has a mean radius of 0.5 in and a lead of 0.16 in. If the screw has a coefficient of friction of 0.16, the moment needed to unclamp the workpiece is best given by a. 22.5 ft*lb

A self-locking C-clamp is used to hold a workpiece with a clamping force of 5000 lb. The screw has a mean radius of 0.5 in and a lead of 0.16 in. If the screw has a coefficient of friction of 0.16, the moment needed to unclamp the workpiece is best given by a. 22.5 ft*lb

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: What is the low limit on the smallest outside diameter?

A: Solution:

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18) Distance=4.2-0.66 =3.54 in

Q: Part C - Radius of curvature for AB and BC Determine the radius of curvature for AB, PAB, and for…

Q: 4. The surface temperature of the hot side of the furnace wall is 1200 degrees C. It is desired to…

Q: What process does this following sample have gone through? I. none II. quenching III. annealing IV.…

A: ALL THE OPTION ARE HEAT TREATMENT PROCESS LIKE ANNEALLING ,QUENCHING AND COLD ROLLING .

Q: How did you determine to round up to 55 mm if the table never mention anything about 55 mm?

A: H=55 mm

Q: In Part a, could you please explain where the 4 comes from on the line before the answer.

Q: Choose one of the following statements which is not true.

A: for solution refer below images.

Q: How would tou answer #10?

A: As mentioned in the question to solve #10, i will solve only question 10th

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: R L2 (Side view) (End view)

A: Given data: α (Bend angle) =70° Kba (Strecth factor) =0.33 t (Stock thickness) = 0.3" R (Width…

Q: What unit is the 0.000931 ?

A: Torsion equation is given by, TJ=τr=GθLwhere,T = torque acting or applied in N-m or N-mmJ = polar…

Q: what happened with the 10 in the first equation?

Q: If rods of these materials are the same size, select the lightest metal rod. Titanium Carbon…

Q: What's the answer C onwards with working and correct answer and can you label it please as I have…

A: The ideal diesel cycle does not occur in practical life because the losses are not eliminated in…

Q: Please answer questions 7,8, show reasons and examples

A: The characteristic equation of the system is:x^6 + (73*x^5)/40 + (1969*x^4)/48 + (22309*x^3)/600 +…

Q: How do you solve parts a,b and c?

Q: what is the bottom length?

A: To calculate the bottom length

Q: I need these two parts answered (Multiple Choice). If you can not answer all two parts please leave…

A: Problem 1To determine the tolerance specified for the depth of groove in the enlarged view, refer to…

Q: The impact test is used to find a material's it's ability to absorb energy before it fractures. O.…

A: About impact test. Impact test is used to determine the dynamic toughness material. In this test a…

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: How do you solve a and b?

A: Given: To find: Position of knee in figure a) Value of θ1 & θ2 in figure b)

Q: With reference to the drawing callout in Figure 4 below, which part(s) would 'pass' or 'fail'…

Question

What is the correct answer?

A self-locking C-clamp is used to hold a workpiece with a clamping force of 5000 lb. The screw
has a mean radius of 0.5 in and a lead of 0.16 in. If the screw has a coefficient of friction of 0.16,
the moment needed to unclamp the workpiece is best given by
a. 22.5 ft*lb
b. 44.3 ft*lb
c. 270 ft*lb
d. 532 ft*lb
[1]
Workpiece

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given

VIEW

Step 2: To calculate helix angle and friction angle

VIEW

Step 3: To calculate the moment for unclamping

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

7. A pulley 610 mm in diameter transmits 37 KW at 600 rpm. The arc of contact between the belt and pulley is 144 degrees, the coefficient of friction between the belt and pulley is 0.35, and the safe working stress of the belt is 2.1 Mpa. Find: A. The tangential force at the rim of the pulley. Ans. 1.93 KN B. The effective belt pull. C. The width of the belt used if its thickness is 6 mm. 200 a wide Ans. 1.93 KN Ans. 261 mm
4.) A flat belt makes contact with an 16 in. diameter pulley through half its circumference. If the coefficient of friction is 0.45 , and a torque of300ft−bsis to be transmitted, calculate the belt tensions. (please type answer not write by hend)
4.) A flat belt makes contact with an 18 in. diameter pulley through half its circumference. If the coefficient of friction is 0.45, and a torque of 350 ft-lbs is to be transmitted, calculate the belt tensions.
Please solve this question in handwritting. Again in handwriting
Please solve this question in handwriting. Again please in writing.
4 - In a set of pulleys, 3 in the top, 2 in the bottom, it is required to lift a load. If 23% of the effort is lost due to friction, what is the maximum load able to be lifted if 230 N Effort is applied.
2. Figure 2 shows a device for lifting bricks and concrete blocks. It comprises two compo- nents ABC and BD, with a frictionless pin at B. Determine the minimum coefficient of friction required at A and D if the device is to work satisfactorily. W all dimensions in inches Figure 2 D
2. A square threaded screw of mean diameter 25 mm and pitch of thread 6 mm is utilised to lift a weight of 10 kN by a horizontal force applied at the circumference of the screw. Find the magnitude of the [Ans. 966 N] force if the coefficient of friction between the nut and screw is 0.02. A bolt with a squore threaded screw has mean diameter of 25 mm and a nitch of 23 mm It carries an
4 Answer should be in 3 desibal
A C-clamp whose screw has a mean radius of 8 mm, lead of 5 mm, and coefficient of static friction of 0.20 is loaded by the forces shown. For F = 120 N and a = 32 mm, the clamping force holding the workpiece is best given by a. 1.57 kN b. 6.28 kN c. 5.44 kN d. 3.14 Г A 4000/ 7 A F F-a- VIEW A - A Workpiece F
Given problem: Determine the maximum force 'P' that can be applied without causing movement of the 248.8 lb crate which has a center of gravity at point 'G' . The coefficient of static friction at the floor is ?? = 0.4. a) Determine the maximum force ‘P’ that can be applied against sliding in lb. b) Determine the maximum force ‘P’ that can be applied against tipping in lb. c) Determine the safest maximum force ‘P’ that can be applied without causing movement in lb.
a b c d h 82 mm 139 mm 39 mm 18 mm 33 mm Clamps like the one shown are commonly used in woodworking applications. This clamp has the dimensions given above, and its jaws are 38 mm wide (in the direction perpendicular to the plane of the picture). The screws of the clamp are adjusted so that there is a uniform pressure of 190 kPa being applied to the workpieces by the jaws. Find the force carried in each screw.Note: Assume that A, B, C, and D act as pins. (Denote tension forces with positive values; compressive forces with negative values.)