Q3) The motor in Figure 3 consumes 50kW and the power factor is 0.8 and behind. This motor is fed from a 220Vrms voltage 100Hz frequency line. Find the capacitance value C, which makes the power factor 1 when connected in parallel to the line. (In Fig.3, An engine consumes 50 kW at a power factor 0.8 lagging from a 220 Vrms and 100Hz line, find capacitors in parallel with the load which makes the power factor 1.)

Q3) The motor in Figure 3 consumes 50kW and the power factor is 0.8 and behind. This motor is fed from a 220Vrms voltage 100Hz frequency line. Find the capacitance value C, which makes the power factor 1 when connected in parallel to the line. (In Fig.3, An engine consumes 50 kW at a power factor 0.8 lagging from a 220 Vrms and 100Hz line, find capacitors in parallel with the load which makes the power factor 1.)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I need help with this homework question.
Problem #7) Specify whether each of the statements are TRUE or FALSE. D Reactive Power is a measure of the average power consumed by reactive (capacitive and inductive) loads. When connected to an AC voltage source, the instantaneous power (rate of energy transfer) supplied to a resistor varies at a frequency that is 2x the frequency of the applied source voltage. The magnitude of the impedance of a capacitor supplied by an AC source will increase as the source frequency increases. An AC source that has an RMS magnitude of 100V will supply the same average power to a resistor compared to a 100V DC source. The voltage across a capacitor is proportional to the rate of change of the current flowing through the capacitor. The magnitude of the impedance of a resistor supplied by an AC source does not vary as the source frequency increases. A complex impedance Z=R+jX, that has non-zero resistive and reactive components, will consume both real and reactive power when supplied by an AC source.…
Please please answer all subparts. I will really upvote
A coil of inductance 159,3mH and resistance 40 ohms is connected in parallel with a 30 microfarad capacitor across a 240V, 50 Hz supply . Calculate 1. Current in the coil and it’s phase angle 2. Current in the capacitor and it’s phase angle 4. Supply current and it’s phase angle
a) Write down the expression of instantaneous voltage for an AC voltage having a Peak value of 220 Volts and a frequency of 50 Hz provided at time t=0, the instantaneous voltage is 220 Volts. What is the instantaneous voltage of the source at time “t = 5 seconds” What is its RMS voltage? b) Two 200Ω resistances are connected in series with one 0.5 H Inductance and two 100μF Capacitance with the power supply of part (a). (i)Draw the circuit diagram of the above network (ii)What is the total impedance of the circuit (iii)What is the max current that flows through the Inductance? (iv)What is the max current that flows through each of the Capacitance? (v)What is the power dissipated in the circuit (vi)What is the power factor of the circuit (vii)What is the resonance frequency of the circuit? (viii) What is the maximum power dissipated by the circuit when it is in resonance
For the current waveform that shown in Figure below Find:- 1). Average value 2). R.M.S value 3). Form factor Current (A) ha 8 10 12 1-2
Please solve with FBD. Note: the resistance of the lamp is 12V
QUESTION S The AC EMF in the electric circuit shown in the figure is given by the following equation E = Enefit R ele L₂ What is the average power in W) supplied by the EMF to this electric circuit if fo-86 V. L₁-86 mH, L₂ 184 mH.C-18 mF. R-4.0 and w -60-rad/s? Content Area #4)
In the figure below, all impedances are in ohms, all voltages are in volts and currents in Amperes. Both sources operate at 60 Hz. X, = 200 n X, = 600 n 80 sin (wt + T/2) x, = 600 2 0.2 ain wt Determine the time dependent current i (A) due to the current Choose... source Determine the time dependent current (A) flowing through the inductance with a Choose... reactance of 200 Ohms due to the current source Determine the time dependent current i (A) due to the voltage Choose... source Choose... Determine the total effective current (A) flowing through the Choose... inductance with a reactance of 200 Ohms
Please solve this question quickly in electric
The sinusoidal voltage trace displayed by the CRO, the time/cm switch is on 50 µs/cm and the volt/cm switch is on 20 V/cm. The width of one complete cycle is 3.6 cm and the peak to peak height is 5.8 cm. Determine the following: The frequency is = The peak to peak voltage is = The amplitude is = The R.M.S voltage is =