Q3: The crank of a slider-crank mechanism rotates counterclockwise at a constant speed of 300 r.p.m. the crank is 150mm, and the connecting rod is 600 mm long. Determine: 1- Linear velocity and acceleration of the midpoint of the connecting. 2- Angular velocity and angular acceleration of the connecting rod at a crank angle of 45° from the inner dead center position.

Q3: The crank of a slider-crank mechanism rotates counterclockwise at a constant speed of 300 r.p.m. the crank is 150mm, and the connecting rod is 600 mm long. Determine: 1- Linear velocity and acceleration of the midpoint of the connecting. 2- Angular velocity and angular acceleration of the connecting rod at a crank angle of 45° from the inner dead center position.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

solve
Two shafts the axes of which intersect but are inclined to each other at 22 degree are connected by means of a universal joint. At what position in the rotation cycle of the drive shaft (i) velocity ratio will be maximum, minimum and unity (ii) the acceleration is maximum
Q5. A hydraulic cylinder imparts motion to point A which causes link BC to rotate about point C as shown in Figure Q5 below. For the instant shown when link AB and BC are at right angle to each other and angle = 36.87°, the velocity V₁ of pin A is 0.5 ms¹ and is increasing at a rate of 2.5 ms². For this position, determine both in magnitude and direction, (a) the angular velocities of links AB and BC, and (b) the angular accelerations of links AB and BC. You must provide clear statement of the applicable kinematic relationship you propose to use and all the relevant calculations in a concise and systematic way. 175 mm VA 125 mm 0 A 125 mm Figure Q5 B
Another very common basic mechanism is the "four-bar" (the ground is considered one of the bars). The class has designed this demonstration four-bar with dimensions 2.2ft , 4.6ft and 1.0ft . In the position shown, coupler BC is horizontal, rocker CD is vertical and are easily found), and crank AB is rotating at a constant angular (therefore dimensions velocity of 11.8 rad/s Determine the angular velocity of rocker CD. NOTE: Magnitude should be entered here, direction in part 2 of this problem. A LAB WAB B 0A counterclockwise. LAD LBC D LCD
Q#02 :The crank of a slider crank mechanism rotates at a constant speed of 170+(23) r.p.m . The crank is 150 mm long and the connecting rod is 400mm long. Determine 1. linear velocity and acceleration of the midpoint of connecting rod? 2. angular velocity and angular acceleration of the connecting rod, at a crank angle of 40° from inner dead center position?
1. At the time the crank AC is at 30° the collar is 6" from point A and crank BC is horizontal. The crank AC is rotating at 3 rad/s counter clockwise. The collar C is free to slide on the frictionless crank AC. What is the total acceleration of point C? 3" В A
evening3 pdf.pdf Downloads/evening3%20pdf.pdf Q ☆ 1/1 65% Q1/The dimensions and configuration of the four bar mechanism shown in figure are follows: AB = 30 cm, CD = 36 cm, BC = 36 cm and AD = 60 cm. The crank AB has an angular velocity of 10 rad/sec clockwise. Determine the angular velocity of BC and velocity of the joint C. Q2/. Four masses ml. m2. m3 and m4 are 200 kg. 300 kg. 240 kg and 260 kg respectively. The corresponding radii of rotation are 0,2 m.015 m. 0.25 m and 03 m respectively and the angles between successive nasses are 45 75 and 135 Find the position and magnitude of the balance mass required. if its radius of rotation is 0.2 m 909 2126/ O D
5
theory of machine
first 3 parts
First pulley Second pulley FIGURE 2 FIGURE 2 shows a block of mass m, is hung from the double pulley system. Each pulley has the same mass m, and same radius R. When a downward pulling force of F is exerted, first pulley and second pulley rotate with angular accelerations of a1 and a2, the block accelerates upwards with linear acceleration of a. The rotating second pulley also in the same time accelerates upwards with linear acceleration of a. The rope does not slip over the pulley. (a) Draw free body diagrams separately for the first pulley, the second pulley and the block. (b) By treating the pulleys as uniform discs, state the required equation to determine the moment of inertia of the pulley. (c) State the equations if you are going to determine the magnitude of the downward pulling force F. The equations must be related to Newtn's second law for rotational motion and Newton's second law for linear motion.
a. Which term(s) in this equation is/are eliminated if Point A is stationary? b. Which term(s) in this equation is/are eliminated if Frame A rotates with constant angular velocity? c. Which term(s) in this equation is/are eliminated if Frame A is fixed to a rigid body and Point B is a point on that body? d. From a definition of position vector FB/I = TA/I + TB/A, derive the expression for acceleration below TA/I 144 A TB/1 TB/A B B/1 = A/I +B/A+A/I XTB/A+20A/I XUB/A+WA/IX (WA/IXTB/A)