i need the answer quickly Q3: For the Single Line Diagram shown below, draw the reactance diagram andspecify all reactance in . u.. Take Sb = 100 MVA, V = 33 kVM.) 40 MVA. x,-0.20 pu30 kVT₁60 22G38110MVA100 MVA.33 kV= 0.15 pu110 MVA110/33 kV(M) 20 MVA * = 0.20 pu30 kV33/110 kVX₁, -0.08 pux=XT2= 0.08 pu

In this question, We need to draw the single line diagram for the base voltage VB and SB ?…

Q3: For the Single Line Diagram shown below, draw the reactance diagram and specify all reactance in .u.. Take Sb = 100 MVA, Vb = 33 kV M. 40 MVA. x,-0.20 pu 30 kV T₁ T₂ 60 Ω 38 38 110MVA 100 MVA. 33 kV % = 0.15 pu (M) 20 MVA x = 0.20 pu 30 kV 33/110 kV X₁, -0.08 pu 110 MVA 110/33 kV X1₂ = 0.08 pu

Q3: For the Single Line Diagram shown below, draw the reactance diagram and specify all reactance in .u.. Take Sb = 100 MVA, Vb = 33 kV M. 40 MVA. x,-0.20 pu 30 kV T₁ T₂ 60 Ω 38 38 110MVA 100 MVA. 33 kV % = 0.15 pu (M) 20 MVA x = 0.20 pu 30 kV 33/110 kV X₁, -0.08 pu 110 MVA 110/33 kV X1₂ = 0.08 pu

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Ture or false
What is ampere circuital law?
3. Which of the following statements about the use of structural steel as an equipment grounding conductor(EGC) in an AC system is correct?A. Structural steel isn't allowed for use as an EGC.B. Structural steel can be used as an EGC bonding jumper between panelboards.C. Structural steel must have an EGC bonding jumper every three feet of structure.D. Structural steel can be used as an EGC when it's bonded at both ends.
Estimate the length of conduit to perform the next bends. EMT will be bend using a hand bender. Provide your answer in inches (just the number) using up to 2 decimals. The picture shows two panels connected by a back-to-back 23.5" stubs EMT 3/4" 6.25 ft P
b) Remove the following complements using DeMorgan's theorems. ______________________ ___________________ _____________ P+ Q + (C+D.E'). (F+G) Please write the solution handwriting.
The contractor is controlled by?
i need the answer quickly
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
22surse_assessment_id=_18982_1&course_id=_22058_1&content_id= _262244_1&ques * Question Completion Status > A Moving to another question will save this response. uestion 2 If the switch is closed for a long time and then opened at t-0. What is the initial value of the capacitor's voltage? ww None of the answers o 12 O Take Test: Quiz 2-. FUJITSU F10 F11 F12 Prt Scr E7 F8 F9 F6 Sys Rq ECO 7 V 8 A 9. 5 Y ! U P
Select the best answer from multiple choices: 1. The system e'e-5 is: a. Linear, time invariant, casual. b. Non-linear, time invariant, non-casual. c. Non-linear, time varying, casual. d. Not all the above. 2. Noise can be reduced through: a. Increasing So. b. Increasing Si. c. Both (a) and (b). d. Note all the above.
The wording that I am running into with questions such as "The number of conductors required to be installed between three-way and four-way switches is " is confusing. The text is not expalining this in a way that I am understanding anything other than grounding conductor, which is optional unless I am using a metal box. So what type of "conductor" is beng discussed?
Complete the following text with words Pt100 sensors are a specific type of _____(1) detector. The most important characteristic of Pt100 elements is that they are made of _____(2) with an electrical resistance of _____(3) ohms at a temperature of ______(4) °C and temperature coefficient ____(5). It is by far the most common type of RTD sensor. The other materials with which RTDs are built are: ___(6), _____(7), ______(8). The most recommended conditioning method is reading at _____(9). Typically, a _____(10) behavior of the Resistance-Temperature relationship can be assumed.