Answered: Q3) Determine the total number of…

Q3) Determine the total number of 3/4-inch, A325 bolts required for the tension splice in Figure. The threads are not in the shear planes. use LRFD. * A36 steel 1 3" 3" 14"

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear plane. No slip is permitted. Both the tension member and the gusset plate are A36 steel. These bolts have not been added to distribute loads in the filler and two fillers are used. Use LRFD for solution. What is the design strength for block shear in kip? Express your answer in two decimal places. 2" 3" 2" 1/2" thick Gusset Plate O 2" 3" 3" 2" 3/8" thick P
1. In the butt joint shown below, the 7/8-inch diameter bolts are made of A325 steel with threads excluded from the shear plane and the plates are made of A36 steel. 12 in. xin. 100 12 in. a) Determine the bolt shear strength b) Determine the bearing strength of the plate c) Determine the tensile strength (both gross and net) of the plate d) What is the strength of the bolted connection?
At the connection at point C, 4 M20 bolts are used to connect the U150x75x6.5x10 profile with the gusset plate, tb = 10 mm. The quality of U profile steel and gusset plate is BJ41. Bolt quality is A490M with shear plane on the non-threaded part. a) Check the bolt clearance requirements in the direction of the force. b) Check that the shear strength of the bolt is sufficient to withstand the factored load SUBC. c) Determine the distance between the bolts, s, so that the bearing strength of the connected plates is sufficient to withstand the factored load SUBC. Baut M20 - S, BC U150x75x6,5x10 Pelat buhul, t = 10 mm Kolom WF 300x300x10x15 (satuan dalam mm) 81
Please answer all the questions with a complete solution. thank you.
A double lap splice connection shown in figure B is made up of 6mm x 150mm and 9mm x 150mm. Use NSCP specifications and assume a double row of bolts with standardsize holes for a bearing type connection with threads excluded from the shear planes.Minimum tensile strength Fu = 552.93MPa. Assume diameter hole is 3mm bigger than thediameter of bolts. Allowable shear stress is Fv = 207MPa. Allowable bearing stress fb = 1.2Fu.Diameter of bolts is 19mm. Fy = 449.25MPa.(a) Compute the tensile capacity of the steel plates. (Max. Net Area = 0.85 of Gross Area)(b) Compute the number of 19mm diameter bolts to develop the full strength of the plates. Note: SHOW DRAWINGS AND SOLUTIONS.
1. An L 178 x 102 x 19 with one line of 20mm diameter bolts in each leg in usual gage as shown. Assume the connection length is 450mm. The pitch distance for the subsequent standard size holes is 75mm. Use ASTM A572M Grade 345 steel materials and : a. Determine the design strength of the member. b. Specify the maximum permitted length of the member as per AISC specifications.) 102mm g g 19mm 178mm L 178 x 102 x 19 Gusset Plate
1. In the butt joint shown below, the 7/8-inch diameter boits are made of A325 steel with threads excluded from the shear piane and the plates are made of A36 steel. o of a Determine the bolt shear strength b) Determine the bearing strength of the plate ) Determine the tensile strength (both gross and net) of the plate d) What is the strength of the bolted connection?
Problem 1: A butt joint shown in Figure ST – 127 using A325 bolts with a diameter of 16 mm with threads excluded in a shear plane. The plate used is A36 steel with Fy = 400 MPa. Use LRFD. Hole diameter is 3 mm larger than the bolt diameter. 1. Compute the design strength Pu of the connection based on bearing of the plate. Hint: The inner plate will govern. No need of checking the outer plate. 2. Compute the design strength Pu of the connection based on bolt shear. Hint: the bolt is in double shear. As is times 2 for every bolt. |32 84 84 12.5 mm T/2 T/2 22 mm 12.5 mm T/2- T/2 + T 180 mm Figure ST - 127
Tension Member -Problem 2 9 - 4" Bolts Gusset Plate Plate thickness t = ½" 2" Tension Member A36 Steel Plate 3" P, 10" и 3" d h Compare Tension Capacity of line 2" e abcde and line An Ag fgchi 4" 4"
Q3) Determine the total number of /4-inch, A325 bolts required for the tension splice in Figure. The threads are not in the shear planes. use LRFD. A36 steel 14" 3" 3" 12" 2 @ 12" t = /g" Рp — 35 k PL = 86 k t = /g". t= "
Compute the net area of the given members.