Q3- A steel pressure vessel is sealed by a steel gasketed cap fastened with 8 preloaded bolts as shown in figure below. The cylinder stores gas at a maximum pressure P=1200 psi. The thickness of the gasketed cap is e=0.5 in, the diameter of the cylinder is de = 3.25 in, and the diameter of the bolt circle is db=5.5 in. Also, tp-0.5 in. It has been decided to use 7/16 -14 UNC 5/4 (L=bolt length) SAE Grade 8 hex-head bolts with washer. You may assume a non-permanent connection. Determine the load factor ni, and the joint separation factor no. (Elasticity modulus for steel, Esteel=30 Mpsi) Note: P (load per bolt) = Pg AJN, where A, is the area of the cylinder. dpe de 000

Q3- A steel pressure vessel is sealed by a steel gasketed cap fastened with 8 preloaded bolts as shown in figure below. The cylinder stores gas at a maximum pressure P=1200 psi. The thickness of the gasketed cap is e=0.5 in, the diameter of the cylinder is de = 3.25 in, and the diameter of the bolt circle is db=5.5 in. Also, tp-0.5 in. It has been decided to use 7/16 -14 UNC 5/4 (L=bolt length) SAE Grade 8 hex-head bolts with washer. You may assume a non-permanent connection. Determine the load factor ni, and the joint separation factor no. (Elasticity modulus for steel, Esteel=30 Mpsi) Note: P (load per bolt) = Pg AJN, where A, is the area of the cylinder. dpe de 000

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

L = 0.3m A = 20 x 6 mm E= 70 GPa allowable stress = 120 MPa 0.6 m 0.4 m 0.2 m Rigid bar D C W 0.5m 40 x 6 mm 50 GPa wable stress = 80 MPa 16 mm dia. bolt with allowable s 6 mm 80 MPa in bearing and 60 MPa The rigid bar A,B,C,D shown in figure is connected to the ground by a hinge at B and to Magnesium bar at A, Aluminum bar at C. the properties of the bars are shown on the figure. all the connections are using 16 mm bolts in single shear. Determine the maximum safe load W that can be applied. Determine the final position of point D.
Hi, I need help with this question.
With FBD and Solution pls refer to the second picture if the answer is in the choices one of those 5 answers is correct
A thin-walled spherical vessel, which is made of AISI C1020, as rolled steel has a diameter of 2.5 ft. The joint efficiency of the vessel is 80%. Internal pressure of the gas inside the vessel varies continuously from 200 psi to 400 psi. If for a Factor of Safety of 1.75 based on Soderberg criterion and the surface of the vessel is polished, find the minimum safe thickness of the vessel.
The following figure shows the critical position of a crane that supports 2.5 Tons of load by means of a chain. You are delegated the responsibility of building a crane with similar geometric characteristics and load capacity. The diagram of free body of the crane arm can be redrawn as follows. (check the attached image "fbd") Assuming that the crane arm will be made of steel with yield stress sigmaY =220 MPa and that you must consider a safety factor of F.S.=1.5, propose a profile from the following catalog for the manufacture of the crane arm. Ignore the effects of shear forces on this element. On the other hand, it is very important that you consider the effects of axial loads. Commercial profiles for arm construction. (Check image "profiles")
A steam boiler, d meter in diameter and L m in length, is made of hard steel, generates steam at a gauge pressure of p N/mm2 . Assuming the efficiency of the riveted joints as e %. It is closed at both ends by flat cover plates which are made of Mild steel and freely supported. 1. Determine the wall thickness of the cylinder if the ultimate tensile stress = A MPa and factor of safety = B. 2. Calculate the minimum thickness necessary of the cover plates with uniformly distributed load, if the the yield point stress is C MPa and factor of safety of F. 3. Also find the increase in internal diameter, the increase in length and the increase in volume. Take E = 200 kN/mm2 and u = 0.3. d= 1.1 L= 1.54 ; p= 5.68 ; A= 328 B= 4.6 ; C= 494 ; F = 3 e= 69
An aluminum alloy [E = 10,000 ksi; oy = 40 ksi] pipe (1) is connected to a bronze [E = 16,000 ksi; ay = 45 ksi] pipe at flange B. The pipes are attached to rigid supports at A and C. Pipe (1) has an outside diameter of 2.425 in., a wall thickness of 0.21 in., and a length of L₁ = 8 ft. Pipe (2) has an outside diameter of 5.00 in., a wall thickness of 0.20 in., and a length of L₂ = 14 ft. If a minimum factor of safety of 2.1 is required for each pipe, determine: (a) the maximum load P that may be applied at flange B. (b) the deflection of flange B at the load determined in part (a). Deflection to the right is positive. (2) (1) C Answer: (a) P = i (b) Ug = i P< L₁ B L₂ ! kips in.
Calculate the wall thickness required for a thin-walled cylindrical pressure vessel which must withstand an operating internal pressure of 3.5 MPa at an outside pressure of 2 MPa. The mean diameter is 200mm and the stress must not exceed 60 Mpa. O a. 8.3 mm O b. 2.5 mm O c. 3.3 mm O d. 5.83 mm O O
MPa) which requires at least a pressure of 10 MPa to prevent leakage. Problem 8.5 A joint in the figure uses a compressed asbestos gasket (E-480 Dimensions are in mm 10 20 200 100 D 150 The cover plate is tightened by using 8, metric grade 5.8, M10x1.5 bolts. If the cylinder is to be rated for an internal pressure of 3500 kPa, calculate the necessary tightening force per bolt for a factor of safety of 2.