An aluminum alloy [E = 10,000 ksi; Oy = 40 ksi] pipe (1) is connected to a bronze [E = 16,000 ksi; oy= 45 ksi] pipe at flange B. The pipes are attached to rigid supports at A and C. Pipe (1) has an outside diameter of 2.475 in., a wall thickness of 0.19 in., and a length of L1 = 10 ft. Pipe (2) has an outside diameter of 4.60 in., a wall thickness of 0.18 in., and a length of L2 = 17 ft. If a minimum factor of safety of 1.8 is required for each pipe, determine: (a) the maximum load P that may be applied at flange B. (b) the deflection of flange B at the load determined in part (a). Deflection to the right is positive.

Q: A 7.9-m-long steel [E = 195 GPa] pipe column has an outside diameter of 229 mm and a wall thickness…

A: Given:The length is .The modulus of elasticity is .The outside diameter is .The thickness is .The…

Q: Considering Figure 20-8 (textbook), the torsion geometry parameter, Jw, for case 4 when b-6 and d=9…

A: b=6d=9

Q: If the horizontal displacements of nodes 2 and 3 of the following element are q2=0.2 mm and q3=-0.1…

A: Given: Here are the given data, q2=0.2 mmq3=-0.1 mm To find: The horizontal displacement of point…

Q: Using the sample set of readings provided for Experiment 1 and taking the Young's Modulus of steel…

A: i hope its helpfull.thank you.

Q: The two cylindrical rod segments shown in the figure below (Figure 1) are fixed to the rigid walls…

A:

Q: Given the applied load and properties of a simply supported I-beam, determine the initial…

A: Given Data

Q: An aircraft engine develops 150kW at 1500rpm. The engine output shaft is steel which fails when the…

A:

Q: how did you find the equation for L in step 2 and also why isnt h mulplied by the Area when solving…

A:

Q: The axial assembly consists of a solid 1-in.-diameter aluminum alloy [E = 11000 ksi, v = 0.26, α=…

A:

Q: Calculate ly the moment of inertia for the composite section about the x-axis. in4 ENTER Calculate…

A:

Q: A bronze pipe (1) is to be connected to an aluminum alloy pipe (2) at flange B. When put in place,…

A:

Q: A circular shock absorber, as shown in the figure below, is designed to support a set of sensitive…

A: Force applied (F): 1000 NDiameter of aluminum circular bar (d1): 4 mmDiameter of hollow circular…

Q: 1. A circular step hydrostatic thrust bearing with outside diameter of 16 in. is to be designed to…

A: As per the guidelines, I can solve only first three subparts at this moment. For rest parts, repost…

Q: Calculate the volume (in ft3) of material used in making 350 ft of 2 in. type L copper tubing. ft3

A: Given data  Length of copper tubing (L) = 350 ft For a 2 in. nominal tube size (from the table of…

Q: (3) P = 0.0400 T= 28.98 x = 0.913 H= 2342.64 H*= -204.85 M = 103.5 (9) P= 1.0135 T= 22 Sub = 78.0 H…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: Assuming a welded rail line, 1km long, that is unconstrained except at the ends. The rail has a…

A: Write the given data.

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.