Q3 A control system is described by the block diagram in Figure 1, where R(s) is reference input and Y(s) is system output. (a) Use Matlab and block reduction techniques to determine the transfer function Y(s)/R(s). (b) R(s) Plot the unit step response of the system output. + I 600 20 S+2 Figure 1 0.2 1 s +3.5 Y(s)

Q3 A control system is described by the block diagram in Figure 1, where R(s) is reference input and Y(s) is system output. (a) Use Matlab and block reduction techniques to determine the transfer function Y(s)/R(s). (b) R(s) Plot the unit step response of the system output. + I 600 20 S+2 Figure 1 0.2 1 s +3.5 Y(s)

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter32: Standby Power Systems

Section: Chapter Questions

Problem 7R: Briefly explain the function of a transfer switch. _____

See similar textbooks

Similar questions

State the advantages and disadvantages of the block diagram reductio technique.
ii. Describe the role of the process reaction curve ( Figure 3 )and the Ziegler-Nichols PID tuning rules (Table 1) in control system design. Tangent line at inflection point Figure 3 Table: 1 Zeigler-Nichols PID controller Tuning rules Type of Controller K, T T P. 00 0.95 125 PI 0.3 PID 2L 0.5L Imnortant Note:
What is equation of the demodulator? advantages and disadvantages of DSB-SC over DSB-AM?
A Data Acquisiton system is used for sensing angular speed with an analog DC Tachometer with asensitivity of 0.05 volt/rpm. The ADC of the system is a 8 bit component and has a full scale of 10V. If the output ofDAC is 101, what is the possible angular speed range?
Please no hand writing solution for other wise down vote
Ex. 1915. An Arduino analog input voltage is 3.160 volts. Arduino PWM output pin drives a low-pass filter, as shown in Figure 1915. The low-pass filter converts the PWM signal back to an average-DC voltage. Arduino specifications include: I/0 voltage range of e to 5VDC; 10-bit A/D input; and an 8-bit D/A PWM output. an analog output DC volage at the low-pass filter. Determine (Vout - Vin). The analog input DC voltage results in
Q2 Figure Q2 shows a Linear Feedback Shift Register circuit. Write down the VHDL entity associated with a 6-bit shift register with the inputs and outputs as shown in Figure Q2. (a) (b) Write down a VHDL architecture for a 6-bit shift register. 6-bit parallel out shift register clk d reset serial_in Figure Q2
1) For purposes of measuring length, the human torso was a convenient tool, and gave us units of---------? A) Meter. B) cm. C) foot. D) mm. 2)---------the output signal consists of a proportion of the external voltage source applied across the two ends of the potentiometer. A) Null-type, B) deflection-type ,C) passive instrument „D) active instrument. 3) The prerequisite for the reduction of systematic errors is a complete analysis of the----? A) Measurement system, B) systematic errors, C) System disturbance, D) Errors. 4) The extent to which series mode noise corrupts measurement signals is measured by a quantity known as--- A) noise ratio , B)Dual signal-to-noise ratio , C) A&B , D) signal-to-noise ratio . 5) Sometimes used to provide shielding from capacitive-coupled noise, but the necessary supports for the conduit provide multiple earth points and lead to the problem of-------? A) Shielding, B) Multiple earth, C) Earth loops, D) Noise.
1a. Why is the input impedance to a JFET so high? b. Why is the terminology field effect appropriate for this important three- terminal device?
Describe the concept of transfer functions and their application in control systems.
Sketch each of the following special digital sequences: a. 58 (n) b. -28 (n-5) c. -5u(n) d. 5u(n-2)
Answer this question. It a question from electrical engineering and the course is Analogue to digital conversion. The topic is Digital Modulation