Q3/ A buck-boost converter generates an output voltage of range 10-14V in CCM. The input voltage is 12V. Consider all components to be ideal. A) Draw the circuit B) Calculate the duty ratio range to get the required voltage range C) Calculate the minimum inductance to stay in CCM if the frequency of switching is 40KHZ and the load resistance is 500 D) Using the calculated minimum inductance value in (C) with the same frequency. Calculate the output voltage of the converter when the duty ratio (8) is 50% and the load resistor is 150 Q

Q3/ A buck-boost converter generates an output voltage of range 10-14V in CCM. The input voltage is 12V. Consider all components to be ideal. A) Draw the circuit B) Calculate the duty ratio range to get the required voltage range C) Calculate the minimum inductance to stay in CCM if the frequency of switching is 40KHZ and the load resistance is 500 D) Using the calculated minimum inductance value in (C) with the same frequency. Calculate the output voltage of the converter when the duty ratio (8) is 50% and the load resistor is 150 Q

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Fill in the blanks. I would love to see how to get the correct answers.
II- Research how engineers dispose of the waste produced by the generation of nuclear energy. Be specific and provide details. Please cite sources for all research completed while answering this question. Explain in detail regulations and environmental concerns that may apply (include a minimum of three – more is better). Be specific and provide details. Please cite all your sources. Which field(s) of engineering is involved with these disposal Projects? Are these fields of engineering of interest to you? Why or why not. Explain in detail Answer all 3
Help please
Question.
Complete solution otherwise skip. Plxxx.
We are running 3 wires and a ground in a RMC to a control panel with a 60 amp circuit breaker disconnect in the control panel. The conduit is run along the ceiling where the ambient air temperature is 100 degrees. The control panel feeds our secondary cooling pump. What size are the ungrounded conductors? All conductors have typeTHHN insulation. A #6 AWG B 600 Kcmil C #8 AWG D #2 AWG What size RMC do we need? A 3" B 3/4" C 1" D 1 1/2"
b) Remove the following complements using DeMorgan's theorems. ______________________ ___________________ _____________ P+ Q + (C+D.E'). (F+G) Please write the solution handwriting.
Please provide Handwritten answer. Electrical Engineering A 15 KHz tone is recorded at 8000 Hz. The frequency of the tone when played back at 8000 Hz is ____ KHz
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
Please, I need the final solution as soon as possible, I do not need any explanation or explanation
Please answer quickly. 17. The filament of incandescent lamp is usually made of: a. copper b. silver c. aluminum d. tungsten 18. A current measuring instrument can be modified to measure voltages by: a. using thicker wire in the coil b. using a high resistance shunt c. adding resistance in series d. adding resistance in parallel 21. "When two power sources are connected in a series-aiding configuration, the output voltage equals the _____________" a. supply with the highest voltage b. supply with the lowest voltage c. difference of the two supplies d. sum of the two supplies