Q21. What is the drive output frequency when switch S1 only is closed and the analog inputsare connected to a potentiometer set to its 80% maximum position (8V analog input)?Asume that the potentiometer allows for a speed range from zero speed to maximum(70Hz) speed as the input voltage ranges from 0V to 10V.(a) 18 Hz(b) 35 Hz(c) 52 Hz(d) 56 Hz(e) 70 HzQ22. What is the drive output frequency when switches S1, S4, S5 and S6 only are closed?(a) 72 Hz(b) 70 Hz(c) 68 Hz(d) 65 Hz(e) 55 HzQ23. Which switch (closed) combination will produce an output frequency of 50 Hz andreverse rotation?(a) S2 and S4(b) S2 and S6(c) S2, S4 and S5(d) S2, S5 and S6(e) S2, S4 and S6 Q18-Q25 refer to the figure below:Logic input assignmentsLIIForwardL12ReverseL13DC injection brakingL142 preset speedsLIS4 preset speedsLI68 preset speedsPreselected speeds settingsSP2Hz25SP3Hz30SP4Hz35SP5Hz40SP6Hz45SP7Hz50SP8HzSP9Hz5560OPWR+24TFR Max. outputfrequencyLSP Low speedHSP High speedHzHzHzWiring schematic599 399S2S3 S4 S5 S6TCC 2/370.015.065.0

According to the question, for the given wiring schematic as shown below We need to find the…

Q21. What is the drive output frequency when switch S1 only is closed and the analog inputs are connected to a potentiometer set to its 80% maximum position (8V analog input)? Asume that the potentiometer allows for a speed range from zero speed to maximum (70Hz) speed as the input voltage ranges from 0V to 10V. (a) 18 Hz (b) 35 Hz (c) 52 Hz (d) 56 Hz (e) 70 Hz Q22. What is the drive output frequency when switches S1, S4, S5 and S6 only are closed?

Q21. What is the drive output frequency when switch S1 only is closed and the analog inputs are connected to a potentiometer set to its 80% maximum position (8V analog input)? Asume that the potentiometer allows for a speed range from zero speed to maximum (70Hz) speed as the input voltage ranges from 0V to 10V. (a) 18 Hz (b) 35 Hz (c) 52 Hz (d) 56 Hz (e) 70 Hz Q22. What is the drive output frequency when switches S1, S4, S5 and S6 only are closed?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

write true or false in the following sentences: 1. Load torques which always oppose the motion and change their sign on the reversal of motion are called passive load torques. 2. The control rectifier drive has low atmature current ripple compare to de to de chopper drives. 3. The main difference between dynamic breaking and regenerative braking of de motor is the disconnection the source from de motor in dynamic braking. 4. Two quadrant operation of de motor can be obtained from thee phase semiconverter. 5. de-de four-quadrant drives can be supply high power than ac-de four-quadrant drives.
4
Q2) A- Draw only Mechanical characteristics of the following special motors (Torque / Slip ): i- Hysteresis motor (ii) Stepper motor (iii) Servo motor (iv)Linear motor (iiv) SRM (vi)Performance curve for PMDC motor.
7. The following table relates to the open-circuit curve of a shunt gen- erator running at 750 rev/min: Generated voltage (V) Field current (A) 10 172 300 360 385 395 0 1 2 3 4 Determine the no-load terminal voltage if the field circuit resistance is 125 N. If the speed is now halved, what is the resultant terminal voltage? At the reduced speed, what value of field circuit resistance will give a no-load terminal voltage of 175 V? (N.C.T.E.C., O.2)
What makes buck converters preferable to regulators?
which figure represents the response of the servo motor according the block diagram?
An armature controlled DC motor has the following parameters: Tf = 0.03 Nm KT = 0.15 Nm/A Imax = 2.4 A KĘ = 0.15 Vs/rad Wmax = 5000 rpm R = 0.8 Ohms 1. Determine the following: (i) The maximum output torque. (ii) The maximum power output. (iii) The maximum armature voltage. (iv) The no load motor speed when e = Emax 2. Plot the following relationships: (i) Torque versus current (ii) Induced voltage versus speed 3. If the above motor is operated at 3000 rpm with a load torque of 0.15 N.m, determine the armature voltage
A 230 shunt motor has a nominal armature current of 60 A. If the armature resistance is 0.15 0. calculate The counter EMF
Question 2 a. Figure 1 shows a block diagram of a DC drive system. Diode rectifier AC supply Power converter SCR Firing circuit Regulator Operator's control station Constant-level DC voltage Variable DC voltage Current (torque) feedback Armature Voltage (speed) feedback Fig. 1: DC Drive System Describe step by step the principle of operation of the system. Shunt field
A three phase six pulse converter having input 430 V 50Hz supply is controlling a de motor. Motor back EMF at 700 rpm is 400 V. Calculate firing angle of the converter when the motor is operating at 600 rpm and 0.7 tunes rated torque. DC motor rating: 700 rpm. 70 kW. 440 N ca
For Electrionic Variable speed drives /Analog speed reference for labvolt serfies 3356-00
Solve