Q20 The moment connection shown generates a maximum tensile or compressive load of 222.8 kips at each flange plate connection with the W14x145 column. Determine if stiffeners are needed by checking the applicable concentrated force strengths. The column is A992 steel and the connection occurs at the middle of the 20ft tall column. Use LRFD. -PL /16 × 9 W14 × 145 W24 x 76 PL "/16 X 9 c) Failure by web local crippling a) Failure by flange local bending b) Failure by web local yielding d) Column is OK without stiffeners

Q20 The moment connection shown generates a maximum tensile or compressive load of 222.8 kips at each flange plate connection with the W14x145 column. Determine if stiffeners are needed by checking the applicable concentrated force strengths. The column is A992 steel and the connection occurs at the middle of the 20ft tall column. Use LRFD. -PL /16 × 9 W14 × 145 W24 x 76 PL "/16 X 9 c) Failure by web local crippling a) Failure by flange local bending b) Failure by web local yielding d) Column is OK without stiffeners

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A single plate tension member (200 mm x 10 mm) is made of 300W Steel. The member is connected through welded connection as shown. Calculate the total effective net area for shear lag Ane of the tension member. Gusset Plate 300 mm -Weld Tension Member Tr
Determine the nominal axial compressive strength of the members shown in the followingfigure. NSCP 2015
A square hollow section is connected to the flanges of ISMB 600 as shown in the above figure. The bracket is subjected to symmetrical vertical and horizontal load of each 50 kN. The size of SHS is 150 x 150 x 6 mm. Find the weld size required for the connection. 150 mm 100 mm ARM 50 KN A A 50 kN 75 75 50 KN 150 11 VIEW-A-A
Compute: - Ix̄ - Centroidal y axis - kL/ry - rx - design compressive strength - allowable compressive strength
Explain please
I NEED ANSWER
DO NO OWAVE www.oukpak.com F06 unic 30KN 150 KN 20KN 3m =30" SOLVE FOR ACL SUPPORT 2m HINGE REACTIONS LN DICATE THE DIRECTICNS e UNITC 20 A B im
Tension member
Steel structure design
A PL 38 X 6 tension member is welded to a gusset plate as shown. The steel is A36 (Fy = 36ksi, Fu = 58ksi). a. The design strength, Pu based on gross area b. The design strength, Pu based on effective area PL % x6 3/8" 6" Cross Sectional area of PL3/8x6 a) Blank 1 b) Blank 2
The single shear connection consists of six 26-mm-diameter bolts. If the ultimage strength of the bolts is 720 MPa, determine the factor of safety for the connection at an applied load of P= 570 kN. P=570 kN
3.8-4 Design the tension members of the roof truss shown in Figure P3.8-4. Use double-angle shapes throughout and assume 8-inch-thick gusset plates and welded connections. Assume a shear lag factor of U = 0.85. The trusses are spaced at 25 feet. Use A572 Grade 50 steel and design for the following loads. Metal deck: 4 psf of roof surface Build-up roof: 12 psf of roof surface Purlins: 6 psf of roof surface (estimated) Snow: 18 psf of horizontal projection Truss weight: 5 psf of horizontal projection (estimated) a. Use LPER htp://www.jamarana.com b. Use ASD. 8' 8 @ 10' = 80' FIGURE P3.8-4 www