Q2. Two rigid bars (BD and DK) are connected by a pin at D. They are stabilized by two rollers (at C and E) and a pin support at D. 20 kN 15 kN 4 2 kN/m 3 10 8 kN/m kN/m 1.5 m|| a. Determine the reaction forces (or the force components) on the roller supports C and E and pin support at D, 7 kN B D K *2mt 6 m *2m¥ 5 m b. Determine the axial force A, the shear force V and the bending moment M functions with respect to given X-Y coordinate system for ONLY THE REGION BETWEEN C and D, (0

Q2. Two rigid bars (BD and DK) are connected by a pin at D. They are stabilized by two rollers (at C and E) and a pin support at D. 20 kN 15 kN 4 2 kN/m 3 10 8 kN/m kN/m 1.5 m|| a. Determine the reaction forces (or the force components) on the roller supports C and E and pin support at D, 7 kN B D K 2mt 6 m 2m¥ 5 m b. Determine the axial force A, the shear force V and the bending moment M functions with respect to given X-Y coordinate system for ONLY THE REGION BETWEEN C and D, (0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The bridge is pinned at A and has a roller at G. A downward load of 12.5 lb is applied at point C, and a downward load of 25 lb is applied at E. The support reactions at the pin and roller are shown on the image. Find the stress in members making up the bridge using either the method of joints or method of sections.
If the load P on the beam below causes the end C to be displaced 10mm downward, determine 4. the normal strain in wires CE and BD. 4 m A B 3 m- -2m
1-15. Determine the resultant internal loadings on the cross section at point C. Assume the reactions at the supports A and B are vertical. 6 ft 6 ft 6 ft 800 lb/ft IB E 4.5 ft 4.5 ft
For the girder shown below, Determine the followings due to a uniform live load of 4 kN/m acting on the top beams. 1- Maximum moment at point B 2 2 1 В C E
4-46. If the gap between C and the rigid wall at D is initially 0.15 mm, determine the support reactions at A and D when the force P = 200 kN is applied. The assembly is made of A-36 steel. A -600 mm P 50 mm B 600 mm 25 mm Prob. 4-46 C -0.15 mm
15-7. Determine the reactions at the supports. Assume O and O are fixed and O is a roller. El is constant. 9 kN/m 6 kN/m please use force method
= The strut AB made from two bars (thickness of each bar = 0.50 in) is connected to a rectangular beam CD (b 0.80 in x h = 7.5 in) at joint B. The beam carries a concentrated load of 2750 lb at the end joint D. (a) determine the minimum diameter of the bolt at B if the shearing stress in the bolt is not to exceed 14000 psi. (b) determine the minimum diameter of the bolt at B if the allowable bearing stress in the bar plate is 20000 psi. Detail of joint B 3 ft (O с A 5 ft O B 6 ft D 2750 lb 3.75 in 3.75 in 0 in 0.80 Strut AB Beam CD (b Xh) Bolt (dmin) -0.50 in
Q12. A continuous beam is built in at A and is carried over rollers at B and C as shown in figure, AB = BC = 12 m. It carries an uniformly distributed load of 3 kN/m over AB and a point load of 24 kN over BC which is 4 m from the support B. Value of E and I are 200 Gpa and 0.2 x 10-3 m2 respectively uniform throughout. Calculate the fixed end moments. %3D
II. Draw (approximately) the moment diagram for column AGF of the portal. Assume all the members of the truss to be pin connected at their ends. The columns are fixed at A and B. Also determine the force in all the truss members. -2 m- 2 m - D 4 kN 1.5 m 8 kN 5 m II. a. Use the portal method and determine (approximately) the reactions at supports A, B, C, and D. b. Use the cantilever method and determine (approximately) the reactions at supports A, B, C, and D. All columns have the same cross-sectional area. K L 9 kN 4 m F H 12 kN 4 m A В D 5 m 5 m 5 m
(3) Two beams AB and BC are pinned connected at B, fixed to wall A and supported by a roller at C. For the loading shown, determine (a) the reactions at the wall support A, (b) the internal shear force and bending moment in the beam at section D, which is located 1 m from the fixed end A. Ans: (a) Ay = 1550 N 1, M₁ = 3800 N-m CCW (b) VD=1438 N, MD = -2290 N-m A 450 N/m D 600 N 2 m 2 m B 400 N/m 2.5m
(6) Determine the reactions at A and B for the beam subjected to the uniform load distribution. Draw the N,V,M diagrams. y I 4 kN/m L--x B 500 mm- A) A 400 mm-
Determine the force in kN of following member of the loaded truss. Indicate whether it is C (Compression) or T (Tension). 1. Reaction at E 2. CD 3. JK