Frame ACGE is on hinge support at A and E and braced at B and F to resist force T = 18kN. a = 2 m b = 1 m c = 1 m a. Find the reaction at D in kN.  b. Find the stress in brace BD if it is made of pipe of ø = 75 mm and thickness = 6 mm.  c. If brace AB is connected to BD consist of two flat bars bolted to post AC at B using 20-mm-ø bolt, find the average shear stress (in MPa) in the bo

Q: Rigid member AC is supported by a pin at A and the vertical steel link BD as shown. The di Lanath…

A:

Q: P. = 30KN Pz = 20KN 4m a = 1 L = 6m R2

A: Let R1=RAR2=RBRA+RB=50KN∑MA=030×1+20×5-6RB=0RB=21.666 KNRA=28.334 KN

Q: The uniform link AB, has a mass of 3 kg and is pin connected at both of its ends. The rod BD, having…

A: The given figure is shown below:

Q: If the gap between C and the rigid wall at D is initially 0.15 mm, determine the magnitudes of the…

A:

Q: III. By any method, solve the axial bar forces of the truss shown, and identify whether it's…

A:

Q: By the moment-areamethod c a lc u la te th e slopes of the e la stic curve at A, B and C and the…

A:

Q: 2. Fine the stress in all the members and the reactions at A of the steel frame as shown in the…

A:

Q: 2. Solve for the normal stresses at members CE, CH and BC in MPa if the area of each trus member is…

A:

Q: If P= 3.3 kN, determine the force in member CE of the truss. Input tension as a positive number and…

A:

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

A:

Q: for sew A the a bove and lim pinjointed and joints. Stiffness also la portal frame, tixed at at 'D',…

A: Frame : A frame is a structure which has combination of beam, column and slab which resist the…

Q: In the truss below, use section method and find the magnitude and kind of force in member BC. 12.5…

A:

Q: The following solid aluminum bar (E = 10,000 ksi; α = 11.70E-06/F) is located between two fixed…

A: Detailed solution is given belowSlight difference in answers due to rounding off Explanation:Step…

Q: (a) The axial stresses in members BC and DE (b) The shear stresses in the pin at A, assuming the pin…

A: given-cross sectional area of member=500mm2diameter of pin=20mm

Q: The frame is subjected to a load of 5 kN which acts on member ABD at D. Determine the required…

A: Given : Load = 5 kN Failure shear stress = 50 MPa FOS = 1.5 Determine the required dia. of pin D…

Q: The shaft consisting of steel and aluminum segments carries the torques T and 3T. Find the largest…

A:

Q: M = i R=( i kN.m i+ i j) KN

A: Given:- To find:- Moment and reaction at A

Q: EX. A steel rod 2 m hong has end fram a support structureand fa end a cross- sectional fa3 cm?. The…

A:

Q: Solve for the normal stresses at members CE, CH, and BC in MPa if the area of each truss member is…

A:

Q: For truss shown, use method of section. A)Compute the reaction at B? (Bv and Bh) B)What is the…

A:

Q: The pin at C is with a diameter C. Assume that the pin at C is supported as stated in the table.…

A:

Q: 5. Bar ABD and bar CEF are connected using a pin at point C and a strut member BE to support a 9000…

A:

Q: Select member FC and CB in the truss to carry the inclined force P. Set the allowable tensile ress…

A:

Q: In the truss shown in given figure the force in member DC is 100 t B 300C

A:

Q: Determine the force in member AB, FE and CD using method of section. A |– 3 m →✦✦✦▬▬4 m —✦✦✦▬ 3 m →|…

A:

Q: A force P of magnitude 1,100 N is applied to the pedal shown satisfies a shearing stress in the pin…

A: Given data,  Applied force P = 1100 N  Shear Stress in the pin = 42 MPa  We have to determine the…

Q: Determine the location e of the shear center, point O, for the thin-walled member having the cross…

A: Given :

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

A:

Q: 3m A 12 kN -3 m 8 kN B F -3 m C -3 m- E D 5m

A:

Q: Determine the force in member BD for the truss using the method of joints.

A:

Q: P₁ kN- P₂ kN- Determine (approximately) the reactions at the base of the columns of the frame shown…

A:

Q: 4m 60⁰ 2kN C 60⁰ 2kN B 8m 30⁰ 2kN A

A: Cut the x-x plane as shown in below solution. Applying equilibrium equation in both x and y…

Q: An unsymmetric moment of M = 5 kN.m is applied on the cross-section of an aluminum beam. Find the…

A:

Q: Given the truss below. Take P₁ 40k, P2= 40k, P3-60k, a= 20ft, h=15ft. a B a a D + The support…

A: use the equilibrium moment equation about A to solve reaction at E

Q: the minimum diameter of the bolt at B if the shearing stress in the bolt is not to exceed 14000 psi.…

A:

Q: ENGINEERING MECHANICS (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS AND FBD LEGIBLY. NO…

A: To find support reaction and force in member EF,DE,DF

Q: 2- Determine the rod forces (FAB, FAC, FBC) of the plane truss system as shown below. Point A is…

A:

Q: 4. Select member FC and CB in the truss to carry the inclined force P. Set the allowable tensile…

A:

Q: The rigid element BCD is supported by a bar AB with a diameter of 25 mm and a connection at C with a…

A: Given Load 50 and 15 kNDiameter 25 and 10 mmTo find out Normal stressShear stress

Q: 2. All members of the truss A B C shown have a cross- sectional area of 500 mm? and all pins have a…

A: We have to determine the value of axial stresses in members BC and DE and the shear stresses in the…

Q: Which of the following is the nearest value for the force at member BD? a. 5kN tension b. 1.7 kN…

A: A truss is given with loading as shown and hinged at D and E. Degree of static indeterminacy, Ds Ds…