3. A 600 lb load is supported by a cable which runs over a pulley and is fastened to the bar DE in figure. Assume all hinges to be smooth and neglect the weight of each bar. Determine the forces acting at: a. Point A b. Point B c. Reaction at point C d. Reaction at point E e. Draw FBD of rod AC f. Draw FBD of rod DE 10' 600

3. A 600 lb load is supported by a cable which runs over a pulley and is fastened to the bar DE in figure. Assume all hinges to be smooth and neglect the weight of each bar. Determine the forces acting at: a. Point A b. Point B c. Reaction at point C d. Reaction at point E e. Draw FBD of rod AC f. Draw FBD of rod DE 10' 600

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given the Truss as shown below with load P and dimension L. Using Method of Joints, determine the following: a.) The External Reaction at Point A in terms of P. b.) The External Reaction at Point E in terms of P. c.) The Force at Member BF in terms of P. L/2 В D F H L/2 A P P E - L- L - L L -
Q1) Determine the force in member BC of the truss shown, the truss is hinged at A and supported on rollers at D, the roller is on a sloped surface with 45° to the horizon. ( all the forces in kN and dimensions in meter). Di Di B D2 E DI Di FI F2
The bridge is pinned at A and has a roller at G. A downward load of 12.5 lb is applied at point C, and a downward load of 25 lb is applied at E. The support reactions at the pin and roller are shown on the image. Find the stress in members making up the bridge using either the method of joints or method of sections.
= The strut AB made from two bars (thickness of each bar = 0.50 in) is connected to a rectangular beam CD (b 0.80 in x h = 7.5 in) at joint B. The beam carries a concentrated load of 2750 lb at the end joint D. (a) determine the minimum diameter of the bolt at B if the shearing stress in the bolt is not to exceed 14000 psi. (b) determine the minimum diameter of the bolt at B if the allowable bearing stress in the bar plate is 20000 psi. Detail of joint B 3 ft (O с A 5 ft O B 6 ft D 2750 lb 3.75 in 3.75 in 0 in 0.80 Strut AB Beam CD (b Xh) Bolt (dmin) -0.50 in
The floor system used in a school classroom consists of a 4-in. reinforced stone concrete slab. Sketch the loading that acts along the joist BF and side girder ABCDE. Set a = 10 ft, b = 30 ft. What is the reaction at point F in kips?
Problem 1 If roller support is added at point C, 20ft. from point A. Determine the following: (Use Conjugate Beam Method) 2 k/ft A B 30 ft El = constant E = 29,000 ksi | = 3,000 in. Required: 1. Reaction at A 2. Reaction at C 3. Moment at A
1. Two members, each consisting of straight and 168-mm radius quarter-circle, are connected as shown and support a 500-N load at D. Draw the FBD of the entire frame and members ABC 168 mm 168 mm A and DBC, including dimensions. Determine the forces in member ABC. Also, calculate the force exerted by member DBC on pin C. B D 100'mm 500 NV +54 mm -252 mm -324 mm Answers: Ax = 275 N→, Ay = 390.625 N ↑, By = 600N Į, ABCX = 375N +, ABCY = 209.375 N↑; DBCX = 0, DBCY = 100 N↑ %3D %3D %3D
Classify the structure shown as statically determinate or statically indeterminate. If statically indeterminate, state the number of degrees of indeterminacy. There are pins at A, E, and F and rollers at B, C, and D. 80 k 50 k 40 k JE |F 20 ft'20 ft - 40 ft----30 ft+-40 ft→+-30 ft ---| 10 ft 10 ft
The bar is snugly fit between points C and A before the loading is applied at Collar B. Assume E = 200 GPa for the steel. The circular bars in the assembly are solid. The bars are solid with a diameter of 15 mm. Assume a fixed rigid support at C and A. A C В 6 kN 3 m 2 m A) Show the FBD and compatibility equation for this problem. B) Determine the support reactions at A and C. (Horizontal forces only) Left side: Fc = Right side: FA =
Determine (approximately) the reactions at the base of the columns of the frame shown in Figure below, and draw (approximately) the moment diagram for girder PQRST and column BGLQ. Use the portal method. R 6 k 10 ft [K 9 k- M N F G H 10 ft 9k - D 10 ft E A B -15 t-+ 15 f -+ 20 f -- 20 ft --
2. The scoop holds a 2,000 N weight concentrated at G. If all links are in duplicate, determine the vertical reaction at joint K (Fxy). Note that HL is connected to the truck body and LKJ is a single member. -320 mm 260 mm B 180 mm 100 mm D 160 mm K 1040 mm 380 mm |200 mm 1120 mm Answer: FKy = 403.3613 N ↑