Q2. A series of motor (Load 1) and lighting (load 2) are connected to an AC source as shown in Figure Q2. The AC source, Vs, supplies 415220° V with frequency 50 Hz. Based on this information: 5Ω 100 mH 15Q Load 1 Load 2 i) Calculate the total load impedance. Vs ii) Calculate the current, I. Figure Q2. (ii) Write the waveform expressions in frequency domain for Vs and I. Draw a phasor diagram consists of Vs and / and state the relationship between Vs and I. Determine the power factor and calculate the real power, reactive power and apparent power. Establish the power triangle for the load. (iv)

Q2. A series of motor (Load 1) and lighting (load 2) are connected to an AC source as shown in Figure Q2. The AC source, Vs, supplies 415220° V with frequency 50 Hz. Based on this information: 5Ω 100 mH 15Q Load 1 Load 2 i) Calculate the total load impedance. Vs ii) Calculate the current, I. Figure Q2. (ii) Write the waveform expressions in frequency domain for Vs and I. Draw a phasor diagram consists of Vs and / and state the relationship between Vs and I. Determine the power factor and calculate the real power, reactive power and apparent power. Establish the power triangle for the load. (iv)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An AC voltage source and a resistor are connected in series to make up a simple AC circuit. If the source voltage is given by AV = AVmax sin(27ft) and the source frequency is 19.0 Hz, at what time t will the current flowing in this circuit be 61.0% of the peak current? 5.922 X Note that the voltage in this AC circuit is a sine function. Did you use the correct units for the argument of the sine function? ms
Power = P = 1200 W. Resistance of heating element R= 1052 Average we need to determine, a. RMS curent drawn by Kettle.
(a) What is the frequency in Hertz and rad/s of the voltage waveform shown on Figure Q1? (b) Calculate the average voltage and rms ac voltage of the waveform shown on Figure Q1. (c) Calculate the total rms voltage of the waveform shown on Figure Q1. (d) The voltage on Figure Q1 is connected across a 0.15 2 resistive load. Calculate the power dissipated in this resistor.
A source of AC emf E₁ = 120/300 volts with an impedance of Z₁ = 2/0° ohms is connected in parallel with another AC source of E₂ = 120/-30º volts with an impedance Z₂ = 2/90° ohms. The two AC source are use to supply a load impedance of Z₁ = 10/-53.10 ohms. Calculate the value of the load current IL. O a. 7.62 amperes O b. 4.42 amperes O C. 5.38 amperes O d. 6.48 amperes
A series resistance – capacitance (R – C) circuit is connected to 230 – volt, 50 cycle AC source. The current through the resistor is 45.45 A and the power taken by the circuit is 5,000 watts. Compute the following: 1.) Power factor angle 2.) Circuit impedance 3.) Ohmic value of the resistor
A source of AC emf E₁ = 100/00 volts with an impedance of Z₁ = 20/0° ohms is connected in parallel with another AC source of E₂ = 100/53.1º volts with an impedance Z₂ = 20/0° ohms. The two AC source are use to supply a load impedance of Z₁ = 20/-900 ohms. Calculate the value of the load current IL. O a. 10 amperes O b. 12 amperes O C. 4 amperes O d. 8 amperes
Define electronegative gases and Compare between SF6 and 02 Insulator? Explain the different schemes for cascade connection of transformers for producing very high ac voltages?
Design a CT-FWR to supply a load of (502) with a waveform of the following specifications: - • Vdc = 12 V • Ripple factor = 0.1 % • the main power supply is (220 Vrms, 50 Hz). Determine the following values: - 1- The value of capacitor filter. 2- The maximum load voltage (VmR) 3- The transformer turns ratio (a). 4- The RMS value of the load voltage. 5- Draw the output waveform. (assume ideal diodes)
Q2. For the circuit shown below, sketch the current waveforms is and io and determine the Average and RMS for both currents. ot io Vs = 220V a = 220° + ot 1002
H.W For general pulse train shown below: A sin (nw,t) 2 A 1, show that ; Dn = 2. for a duty cyele %3D shou that : AT %3D Sinc (nT) To To 3. for a duty syele : To & A= 1 %3D Find Dn .
Subject - Design electrical circuits for single phase AC networks Question - Compare the effect of varying resistance, capacitance and inductance in a pararllel and series AC circuits on voltage resistance and impedance.
please write introduction of Power and Power factor in AC Circuits