Q2. (а) A beam is supported and loaded as shown in Figure Q2(a). Point A is a M UTM pin support and point B is reactions at A and B. a roller support. Determine the support ITM M UTM 30 kN UTM 80 kN/m UTM & UTM 3 UTM UTM 30 :D M UTM 200 kNm A 3D 6 m В 12 m UTM TM UI *TTM FIGURE Q2(a) 3 UTM TM UTM TTM

Q: FIGURE 1. 40 kN 40 kN/m A B 20 kN/m E ए 2 m 1m 4 m 2 m R, R2 What is the maximum intensity of moment…

A: Draw SFD and BMD and answer the questions

Q: Resolve Force in X direction Force=100 N Angle with horizontal is 30 degree

A: Given data-  Force (F) = 100 N  Angle(¢) = 30°

Q: Draw the figure of level and show its parts on it.

A:

Q: E A F D 3 in. in. G -2 in. 1.5 in B

A:

Q: b) Air at 30°C flows through a 70 m long, 2 cm x 2 cm rectangular cross section pipe as shown in…

A: given temp = 30 'c length = 70m size =2cm*2cm velocity = 2m/s angle = 35'c to find  given above 4…

Q: PROBLEM 4. Find the resultant of the forces acting on the frame shown and specify where its line of…

A: Taking equilibrium of forces along horizontal direction, we get…

Q: The image below shows a beam subject to two couples, F₁ = 670 N and F₂ = 760 N. (Figure 4) The…

A:

Q: One of the spring parameters is Pitch Select one: O True O False

A: Pitch is the distance between two adjacent coils of spring measured from the midpoint of the spring…

Q: Replace the three couples with a single equivalent couple. F1 = 100 N; F2 = 80 N, F3 = 50 N The xyz…

A:

Q: Compute degree of static indeterminacy q C L L 1 B

A: Given data : The number of member in beam m=2 The number of joint in beam J=3 Support=1 Pinned and 2…

Q: Please answer this is Resultant of Concurrent Force System

A:

Q: The cord exerts a force of F= 30 kN on the hook. If the cord is 4 m long, z = 2 m, and x component…

A: Given data:Fx=25 KNF=30 KN

Q: Draw shear force Diagram 600 lb 4000 lb ft |C D 10 ft + 5 ft 5 ft-

A: Support reaction : ∑MB=0RA×20-600×10+4000=0RA=100 lb∑FY=0RA+RB-600=0100 +RB-600=0RB=500 lb

Q: On Step 3 where do you get the sin(66.80)? reply asap.

A: Required:Explain sin(66.80) in step 3

Q: | Question 1) Dimension the cross section of the rectangular cross section cantilever bar given ww…

A: From the given date and diagram it is required to find the beam cross section dimension i.e b &…

Q: 10 GN/m² to kip/inch²

A: Given unit is GN/m2 1GN=224808.94kip And 1m=39.37inch

Q: H. G. D. E B.

A:

Q: L i L2 La H2 D H1

A:

Q: a/2 3/2a (a 2a a a/2 Determine the coordinate of the centroid with respect to the barred axes.

A: Centroid is the average position of all the points of an object. To calculate the centroid of a…

Q: What is the magnitude of the fifth force F? What is the direction (∅) of the fifth force F?…

A: GIVEN : Diagram is given along with forces. TO FIND: Fifth Force =?

Q: Problem 4: The two bars can deform elastically. They are pinned at point B. The length of AB is 400…

A: Given  AB= 400 mm  BC= 250mm  E= 250 Gpa  Alpha = 30 °

Q: Q2 All members of the truss in Figure Q2 are to be fabricated from the same stock of thin-walled,…

A:

Q: What is the shear load V and moment M at J?

A:

Q: 7. Provide illustration or example of actual situations with curvilinear motions.

A: Definition - Motion in which the direction of the velocity of a body is variable and the path of the…

Q: 5. Draw profile for AA'. 1500m A' A 2000m B' Øm 5000m

A: A contour is given, we need to draw the profile A-A Topographic Profile:- A topographic profile,…

Q: ENGINEERING MECHANICS

A:

Q: testportal Prelim Exams (MEC101) - B06 QuesIu1I 3I 13 ( P.) The forc o

A:

Q: RI 038 R32 80

A: For the given figure, i had drawned in AUTO-CAD using the following commands 1. CIRCLE COMMAND 2.…

Q: uniaxial tension test is Fy (MPa). Based on the stress state against failure if all stresses are inc

A: von mises theory is theory of plasticity ,general stress matrix is             σ1    τ12       τ13…

Q: 6kN 2 kN\m 3 kN D 6kNm A B A CA 6m

A:

Q: mm 120 20 mm 160 mm 20 mm Shear Force 140KN etermine the maximum allowable shear stre

A:

Alloys

An alloy is an admixture of two or more metals or a metal and a non-metal. Since ancient times, man has been using alloys. Alloying helps to retain the properties of the parent matter, such as hardness, strength, toughness, ductility and is corrosion-resistant. Copper alloys such as brass have antimicrobial properties that help to fight against (Coronavirus disease 2019) COVID-19 and other hospital-acquired infections. Some common alloys are brass, bronze, solder steel, etc. Most alloys have a lower melting point than their constituents. This is due to the presence of a nonmetal as one of the constituents that behaves as an impurity and restricts the raise of melting point.