i need the answer quickly Q2/ The three-phase inverter shown in figure (1) is supplied from a 220V source. The load is a starconnected balanced load of R=150 and the thyristors are in 180 conduction mode.Find the following parameters of the inverterA) The rms phase voltage VpB) The rms line voltage V. 0C) The rms line voltage VL1 atfundamental frequencyD) The rms phase voltage Vp1 atTIDIT3T5DI200V12TSKさKA D:T4D4-1,2fundamental frequencyPhase APhase BPhase CE) The THD per line and phase y M150F) The load power Poavm2R150150Figure (1) Three phase invertercircuit

As per the guidelines of Bartley we supposed to answer first three subpart only for solution of…

Q2/ The three-phase inverter shown in figure (1) is supplied from a 220V source. The load is a star connected balanced load of R=150 and the thyristors are in 180 conduction mode. Find the following parameters of the inverter A) The rms phase voltage Vp0 TTR e) The rms line voltage V, 0-32 C) The rms line voltage VL1 at d. T5 KA D TI DI T3 fundamental frequency 200V T4 12 D) The rms phase voltage Vp1 at D4 fundamental frequency Phase A Phase B Phase C E) The THD per line and phase m F) The load power P avm 150 150 150 Figure (1) Three phase invertercircuit

Q2/ The three-phase inverter shown in figure (1) is supplied from a 220V source. The load is a star connected balanced load of R=150 and the thyristors are in 180 conduction mode. Find the following parameters of the inverter A) The rms phase voltage Vp0 TTR e) The rms line voltage V, 0-32 C) The rms line voltage VL1 at d. T5 KA D TI DI T3 fundamental frequency 200V T4 12 D) The rms phase voltage Vp1 at D4 fundamental frequency Phase A Phase B Phase C E) The THD per line and phase m F) The load power P avm 150 150 150 Figure (1) Three phase invertercircuit

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a) Write down and prove DeMorgan's theorem. b) Remove the following complements using DeMorgan's theorems. ______________________ _________________ _____________ P+ Q + (C+D.E'). (F+G)
Help please
Question.
3. Which of the following statements about the use of structural steel as an equipment grounding conductor(EGC) in an AC system is correct?A. Structural steel isn't allowed for use as an EGC.B. Structural steel can be used as an EGC bonding jumper between panelboards.C. Structural steel must have an EGC bonding jumper every three feet of structure.D. Structural steel can be used as an EGC when it's bonded at both ends.
b) Remove the following complements using DeMorgan's theorems. ______________________ ___________________ _____________ P+ Q + (C+D.E'). (F+G) Please write the solution handwriting.
Please provide Handwritten answer. Electrical Engineering A 15 KHz tone is recorded at 8000 Hz. The frequency of the tone when played back at 8000 Hz is ____ KHz
i need the answer quickly
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
17- The electromechanical breakdown depend on the type of the dielectric between two electrodes a- Right. b- Wrong 18- Basic Insulation Level (BIL) is related to the design consideration of the electric device, while Basic protection (BPL) level is related to protection level of the that device. a Right. Wrong. b- 19- As the voltage regulation increased, receiving end voltage will be reduced. Right. b- Wrong 20- We can be using Solar power generation field as a power factor and voltage profile enhancement in Distribution system. (aRight. b- Wrong. 21- From the general electrostatic theories, the field strength at breakdown is given by: a Eb = V/ do =0.6 [Y/ (€ o Er) ] 0.5. b- Eb V/ do = 0.6 [Y / (€ 0/Er )] 0.5. C- Eb V/ do = 0.6 [ Y/(Eo Er) 20.05. d- Eb V/ do = 0.6 [ Y/ (Eo Er) 10.5. 22- Consider plane electrodes with a solid insulator between them. Find the electric field strength at breakdown, if Young's modulus = 10000 (V.F/m2). and the relative permittivity is (36000 TT). If the…
Complete the following text with words Pt100 sensors are a specific type of _____(1) detector. The most important characteristic of Pt100 elements is that they are made of _____(2) with an electrical resistance of _____(3) ohms at a temperature of ______(4) °C and temperature coefficient ____(5). It is by far the most common type of RTD sensor. The other materials with which RTDs are built are: ___(6), _____(7), ______(8). The most recommended conditioning method is reading at _____(9). Typically, a _____(10) behavior of the Resistance-Temperature relationship can be assumed.