Q2: The plant capacily of a 3-phase generatingStation consists of three generators with ratingas shown in Eig.IOMUA12%IOMUA12%.5MUA6%Fi5HVA5%5성UA5%The generators are connectecd to the station bus-bars from which load is taken through two 5MVAStep-up transformers each having a reactance 5%.Determine the maximum fault MVA. Which thecircuit breakers on i) low voltage side and lii) high.VoltageSidemay ha ve to deal with.

Answered: Image /qna-images/answer/4aaf1645-2283-46cc-9307-4e93d791707f.jpg

Q2: The plant capacily of a 3-phase generating Station consists of three generators with raing as shown in Fig. IOMVA 12% IOMUA 12%. 5MUA -6% 5HVA 5% 5성UA 5% The generators are connectecl to the stationbs. bars from ohich load is taken through two 5 MVA Step-up transformers each having a reactance 5% . Determine the maximum Fault MVA. Which the circuit breakers on i) low voltage side and ii) high. Voltage Side may have to deal with.

Q2: The plant capacily of a 3-phase generating Station consists of three generators with raing as shown in Fig. IOMVA 12% IOMUA 12%. 5MUA -6% 5HVA 5% 5성UA 5% The generators are connectecl to the stationbs. bars from ohich load is taken through two 5 MVA Step-up transformers each having a reactance 5% . Determine the maximum Fault MVA. Which the circuit breakers on i) low voltage side and ii) high. Voltage Side may have to deal with.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A generating station has a maximum capacity of 100 kW and costs $300,000. The annual fixed charges are 12% of the cost of the generating station consisting of 5% interest, 5% depreciation and 2% taxes. Find the fixed charges per kWh generated if load factor is (a) 100% and (b) 25%.
Two transformers A and B of ratings 500 KVA and 250 KVA are supplying a load KVA of 750 at e.8 Pflagging, their open circuit voltages are 400 volt and 410 volt respectively. Transformer A has 1% resistance and 5% reactance and transformer B has 1.5% resistance and 4% reactance. Find ( a ) Cross - current in the secondaries on no - load , ( b ) the load shared by each transformer .
In an installation there is a three-phase load of 300 kVA with a power factor of 0.8 behind, in parallel with a three-phase load of 150 kVA with a power factor of 0.6 ahead. A pure reactive element is connected in parallel, and a unity power factor is obtained at the power input. Indicate the reactant of the element, with a positive sign if it is a bank of reactors, or with a negative sign if it is a bank of capacitors. Just put the corresponding sign followed by the numerical value, without units. The numerical value must correspond to the three-phase kVARS. You can use integer values with no decimal places or up to two decimal places
Problem 2 The circuit diagram of a certain load is presented below. Determine the following: a. The power factor of the load. b. If the load is connected across a 400 Vrms source, determine the real and reactive power consumed by the load. c. From (b), determine the value of the capacitor to be placed in parallel with the load in order to improve the power factor of the load to 95% lagging. From (b), A synchronous motor is installed in parallel with the load to correct the pf. The motor is rated 5 hp operating at 60% efficiency. Assuming that the motor is running at rated power. Determine the apparent power and power factor of the motor in order to improve the load's pf to 95% lagging. 202 500 µF HI + VL -20 mH 5Ω >0.5VL m 15 mH
Practice Problem a. Write the no dal equations for the eircuit shown; and solue for the nodal voltages, b. Determine rhe magnitude and polarity of the ve itage across each resissor. R4 R3 6A 7A
Solve it fast plz
In the transformer circuit below, a load of 2.5cis20° Ohms is connected to the output terminals of the transformer. If the voltage across the load is 230V, determine:a. Load current, I(L)b. Imc. Icd. Source voltage, V
Here X =165 plzzz solve urgent with detail...
A Single Area consists of 3 generating units (G1/G2/G3) with the following characteristics: G1: 250 MVA rating, R1 = 0.02 pu (on the 250 MVA base), initial output P1 = 200 MW. G2: 350 MVA rating, R2 = 0.015 pu (on the 350 MVA base), initial output P2 = 300 MW. 0.03 pu (on the 300 MVA base), initial output P3 = 150 MW. G3: 300 MVA rating, R3 = The frequency of the system is 60 Hz. Assuming D = 1 pu on a common base of 1000 MVA, what is the new generation output for G3 for a load increase of 75 MW? Select one: O a. 190.55 MW O b. None of these O c. 203.38 MW d. 166.01 MW
The output of a station with two alternators in parallel is 40MW at 0.75 power factor lagging. One machines is loaded to 20,000KW at 0.8 power factor lagging. Determine the: a. KVA rating and power factor of the load b. KVA rating and power factor of the other alternator
6. A generating station has the following daily load cycle : 10–12 Time (hours) 0–6 6–10 12–16 16–20 20–24 Load (MW) 20 25 30 25 35 20 Draw the load curve and find (i) maximum demand, (ii) units generated per day, (i) average load, (tv) load factor, II
The maximum efficiency of 10Kw D.C generator is 98% and occurs at 80% of full load. Find the total copper losses at rated load