Q2/ The gross power absorbed by the reverse and forward fields of a single- phase induction motor is 30 w and 160 w, respectively. The engine spins at 950 revolutions per minute. Frictional losses with no load are 70 watts. What is the shaft torque if the number of poles is 6, and the supply frequency is 50 Hz?

Q2/ The gross power absorbed by the reverse and forward fields of a single- phase induction motor is 30 w and 160 w, respectively. The engine spins at 950 revolutions per minute. Frictional losses with no load are 70 watts. What is the shaft torque if the number of poles is 6, and the supply frequency is 50 Hz?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the following switch circuit: A) Derive the switching algebra expression that corresponds one to one with the switch circuit. B) Derive an equivalent switch circuit with a structure consisting of a parallel connection of groups of switches connected in series. (Use 8 switches.) C) Derive an equivalent switch circuit with a structure consisting of a series connection of groups of switches connected in parallel. (Use 7 switches.)
What is RG rating of coaxial cable. Please give me detailed information. Don't copy previously given Answer
i need the answer quickly
i need the answer quickly
4. Do some search about the functionality of Airport Metal Detectors. Explain your answer in a paragraph.
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
Please, I need the final solution as soon as possible, I do not need any explanation or explanation
17- The electromechanical breakdown depend on the type of the dielectric between two electrodes a- Right. b- Wrong 18- Basic Insulation Level (BIL) is related to the design consideration of the electric device, while Basic protection (BPL) level is related to protection level of the that device. a Right. Wrong. b- 19- As the voltage regulation increased, receiving end voltage will be reduced. Right. b- Wrong 20- We can be using Solar power generation field as a power factor and voltage profile enhancement in Distribution system. (aRight. b- Wrong. 21- From the general electrostatic theories, the field strength at breakdown is given by: a Eb = V/ do =0.6 [Y/ (€ o Er) ] 0.5. b- Eb V/ do = 0.6 [Y / (€ 0/Er )] 0.5. C- Eb V/ do = 0.6 [ Y/(Eo Er) 20.05. d- Eb V/ do = 0.6 [ Y/ (Eo Er) 10.5. 22- Consider plane electrodes with a solid insulator between them. Find the electric field strength at breakdown, if Young's modulus = 10000 (V.F/m2). and the relative permittivity is (36000 TT). If the…
I need the complete solution & explanation pls
QUESTION 3 We are running 3 wires and a ground in a RMC to a control panel with a 60 amp circuit breaker disconnect in the control panel. The conduit is run along the ceiling where the ambient air temperature is 100 degrees. The control panel feeds our secondary cooling pump. What size are the ungrounded conductors? All conductors have typeTHHN insulation.
i need the answer quickly
I want to solve both questions please