Q2: Rights of way for transmission circuits are difficult to obtain in urban areas, and cxisting lines are often upgraded by reconductoring the line with larger conductors or by reinsulating the line for operation a t higher voltage. Thermal considerations and maximum power which the line can transmit are the important considerations. A 138-kY line is 50 km long and is composed of Partridge conductors with fiat horizontal spacing of 5 m between adjacent conductors. Neglect resistance and find the percent increase in power which can be transmitted for constant IVsl and IVRI while o is limited to 45° (a) If the Partridge conductor is replaced by Osprey, which has more than twice the area of aluminum in square millimeters. (b) If a second Partridge conductor is placed in a two-conductor bundle 40 cm from the original conductor and a center-to-center distance between bundles of 5 m, and (c)If the voltage of the original line is raised to 230 k V with increased conductor spacing of 8 m.

Q2: Rights of way for transmission circuits are difficult to obtain in urban areas, and cxisting lines are often upgraded by reconductoring the line with larger conductors or by reinsulating the line for operation a t higher voltage. Thermal considerations and maximum power which the line can transmit are the important considerations. A 138-kY line is 50 km long and is composed of Partridge conductors with fiat horizontal spacing of 5 m between adjacent conductors. Neglect resistance and find the percent increase in power which can be transmitted for constant IVsl and IVRI while o is limited to 45° (a) If the Partridge conductor is replaced by Osprey, which has more than twice the area of aluminum in square millimeters. (b) If a second Partridge conductor is placed in a two-conductor bundle 40 cm from the original conductor and a center-to-center distance between bundles of 5 m, and (c)If the voltage of the original line is raised to 230 k V with increased conductor spacing of 8 m.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A three-phase 765 kV, 60Hz, 300 km, line has the following positive sequence impedance and admittance: z=0.0165+j0.3306-0.3310<87.14° 22/km, y=j4.674x10-6 S/km. Identical shunt reactors (inductors) are connected from each phase conductor to neutral at both ends of the 300-km line during light load conditions, providing 50% compensation. The reactors are removed during heavy load conditions. Full load is 1.8 kA at unity p.f. and at 730 kV. Assuming that the sending- end voltage (Vs) is constant, determine the following: a) ABCD parameters of nominal circuit b) Sending end voltage (Vs) and current (Is) c) Percent voltage regulation of the uncompensated line d) Percent voltage regulation of the compensated line
one circuit of a sinlge phase transmission line is composed of three solid 0.5 cm radius wires. the return circuit is the composed of two solid 2.5 cm radius wire . the arrangement of conductors is as shwon in figure below. applying the concept of GMD and GMR , find the inductance of the complete line in millihenry per kilometer
Calculate the limit of TL length at the full-load for three-phase, 450 MVA, 400 kV, 50 Hz, 400 mm² overhead line with equivalent phase spacing 6.93 m. Note: consider only the dominant parameter of the line. (a) single-conductor per phase, (b) two-conductor bundle per phase of 35 cm spacing.
Given a three-phase load of 125 MW at power factor of 0.8 lagging, operating at 69kV, with a transmission line efficiency of 97% and voltage regulation of 95%, and the line length of 50 km, design a transmission line system and determine the best conductor configuration, conductor resistance and inductance, and conductor radius values to achieve the efficiency and voltage regulation set. Assume a two-bundled conductor configuration with GMR of 0.0496 m and bundle spacing of 30 cm.
d) Calculate the per unit voltage drop on the transmission line e) Calculate also the sending end voltage Use an overall base of 100 MVA.
A single circuit 60 Hz transmission line. the conductors are Linnet type with flat horizontal spacing of 17.46 feet between conductors. Determine: (a) Assume that the line is short with a length of 50 miles, calculate the parameters of the line and draw the equivalent circuit. (b) Assume that the line is average with length of 150 miles (Pi-nominal model). draw the pi-nominal circuit for the transmission line and calculate its parameters (Z and Y/2 values, where Z is the series impedance of the transmission line and Y is the shunt admittance).
Prove that the conductor cost for transmission line is inversely proportional to the square of theoperating voltage level and proportionality constant increases with the square of the transmissiondistance. Make assumption if necessary.
Compute up to 4 decimal places but only encode your final answers with only 3 decimal digits
Question 6 – Power Systems Disturbances a) A line has a characteristic impedance of 307.70 and a termination resistance of 6000. Assume that the magnitudes of the initial forward - travelling voltage wave and current wave are 4000V and 13A, respectively. Determine the following: (i) Reflection coefficient of voltage wave. (ii) Reflection coefficient of current wave. (iii) Backward-travelling voltage wave. (iv) Voltage at end of line. (v) Transmission coefficient of voltage wave. (vi) Backward-travelling current wave. (vii) Current flowing through termination resistance. (viii) Transmission coefficient of current wave. lime Raper - Ma
1. Following are types of Transmission Lines EXCEPT A. Medium Line B. Long Line C. Capavitive Line D. Short Line 2. What is the theory used to express the voltage and current relations? A. Per-Phase B. Equavalent Transmission Line Model C. Two Ports Network 3. A 300km transmission line is considered as A. Long Line B. Medium Line C. Short Line 4. For a short transmission line, values for element A B C and D are A. A=1, B=0, C=Z, D=1 B. A=1, B=Z, C=0, D=1 C. A=0, B=Z, C=1, D=1
please help solve this question A 100 km Three-Phase 50 Hz transposed transmission line is composed of bundle of three ACSR, 1,431,000 cmil, 47/7 Bobolink conductors as shown in Figure 2 (a). The Three-Phases (bundled Conductors) have flat horizontal spacing of 11 meters as shown in the Figure 2(a). The conductors have a diameter of 3.8 cm and a GMR of 1.5 cm. The Line is going to be replaced with a six conductor bundle of ACSR, 477,000 cmil, 26/7 Hawk conductors. The conductors have a diameter of 2.5 cm and a GMR of 0.9 cm. The new line will have a horisontal phase spacing of 14 meters as it is going to be operated at higher Voltage rating. The new line is shown in Figure 2 (b). The spacing between the bundles in Figure 2 (a) and (b) is 45 cm. Determine,a) The capacitance for each case and the percentage change in capacitanceb) The inductive reactance for each line and the percentage change.c) The inductance for each case and the percentage change ininductance