Q2\ It is required to use a diodes specified to have a 0.7 V drop at a current of 1 mA. The diodes are to be included in a voltage regulator to keep voltage level at 1.5 V to load resistancel.5 k2 as in the circuit shown in the figure. (a) Determine the value for the resistance R and the current passes through the diodes when connecting the load resistance. +5 V R oVo (b)When removing the load resistance, find how will the output voltage changes with its value? DI RL D2 (c) Estimate the change due to change the load resistance with 750 Q? (Assume the diode small-signal diode modeled calculate all changes in output voltage) are to KK

Q2\ It is required to use a diodes specified to have a 0.7 V drop at a current of 1 mA. The diodes are to be included in a voltage regulator to keep voltage level at 1.5 V to load resistancel.5 k2 as in the circuit shown in the figure. (a) Determine the value for the resistance R and the current passes through the diodes when connecting the load resistance. +5 V R oVo (b)When removing the load resistance, find how will the output voltage changes with its value? DI RL D2 (c) Estimate the change due to change the load resistance with 750 Q? (Assume the diode small-signal diode modeled calculate all changes in output voltage) are to KK

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

From the diode circuit shown below. If E=40 V and RL=400, determine the current supplied from the battery. the voltage across the load resistance. and the voltage across diode D2 if all the diodes are silicon with an internal resistance of 2 0. RL E= a. The Current supplied by battery is b. The Voltage across Load resistance RL is c. The Voltage across diode D2 is
In this Zener diode regulator, the source voltage varies from 6 V to 10 V. Assume that the load current varies between 2 mA and 33 mA, and that the diode is an ideal 3 V Zener diode. What is the largest allowable resistance that will ensure the load voltage remains constant with variations in load current and source voltage? Please enter your answer to 3 significant figures.
1- Explain briefly with figure if exist, the Degenerate semiconductors. 2- When a diode is connected in a Reverse Bias condition, the overall result is a small ne current. Why?
Question 4
Consider the half-wave rectifier shown below. It needs to deliver 0.1 A and an average of 15 V to a load. The source is 60 Hz and the diode has a 0.7 V drop. The allowable ripple is no more than 0.4 V (2.5%). Find: Peak AC voltage Vm of the source a) b) The minimum value of the smoothing capacitor(s) c) Comment on the type of capacitor and its/their values you would use for this amount of capacitance vs(t) K Load UL
In this Zener diode regulator, the source voltage varies from 8 V to 10 V. Assume that the load current varies between 2 mA and 45 mA, and that the diode is an ideal 4 V Zener diode. What is the largest allowable resistance that will ensure the load voltage remains constant with variations in load current and source voltage? Please enter your answer to 3 significant figures.
The four diodes used in a bridge rectifier circuit have forward resistances which may be considered constant at 1 ohm and infinite reverse resistance. The alternating supply voltage is 220 V r.m.s. and load resistance is 580 ohm. Calculate (i) mean load current and (ii) power dissipated in each diode.
This one.
Answer a,b,c,d
. A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 300 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance?
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consisting series connected a resistor and an inductance from a 70.7V (RMS), 50HZ sinusoidal AC source. The firing delay of the thyristor is 90° and the load values are R=10Q, L=0.1 H. Define the load current expression and draw the load current by calculating for first two periods. And calculate the average values of the load voltage and current.
Zener voltage, VZ = 6.1V and incremental resistance, rz = 0 a) Determine the value of Ri such that the Zener diode remains in breakdown if the load current varies from IL = 20 to 200 mA and if the input voltage varies from VI = 8.6 to 10V. Assume IZ(min) = 0.1IZ(max). b) Determine the power rating required for the Zener diode and the load resistor. c) If the position of Zener diode were changed to be in forward bias region, will the voltage regulator still work properly? Justify your answer