Q2/ If positive M of 20kN.m is applied, draw the bending stress distribution. Est =200GPAandEAlu= 10GPA180mmWood20mmSteel100mm

Answered: Image /qna-images/answer/5e5a8392-a0f2-4d3d-a8cb-7b4a8c219d3c.jpg

Answered: Q2/ If positive M of 20kN.m is applied,…

Q2/ If positive M of 20kN.m is applied, draw the bending stress distribution. Est = %3D 200GPA and EAlu=10GPA %3D 180mm Wood 20mm Steel 100mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Help me solve and draw Shear and Moment Diagram. Show complete solution thank you.
30 kN/m 50 kN-m A D 3 m 1 m 2 m A. Write the equations for the internal shear and bending moment for segments 1) Osx< 3 2) 3sx< 4 3) 4sx< 6 where x is the distance measured to the right of point A. Draw supporting FBDS. Calculate all relevant values. B. Using your answer in item A-1, determine the location from point A and magnitude of the local maximum internal bending moment between 0s x< 3 C. Using the equations and values from item A, draw the shear and bending moment diagrams. Solve for Mmax(pos).
Engr statics I check it was wrong answer 245.166 I need to show all work. Topic: Shear and Bending Moment A gantry crane of weight W-100 Kg moves across a bridge with the length 1-5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations
The bending moment diagram and cross-section for a beam are shown below. Use the elastic flexural formula ox = -Mzy/l, to determine the required strength of the beam to resist the compressive stresses. Circle the correct answer for the compressive strength in ksi: 2.3, 2.5, 27.5, 30, 37.7 Show your work below. Bending Moment Diagram Beam Cross-Section 4" +50 2' (K-Fe) 2" 2" - 40 2"
I need the answer as soon as possible
If the sections shown below is subjected to a negative bending moment of 10kN, draw the 3D bending stress distribution. Please show all relevant calculations and values on your distribution. The position of the neutral axis is measured from reference point A.
Draw shear force and bending moment diagrams P= 1000 N .w = 250 N/cm 5 cm 20 cm Figure 1.2 (not to scale)
If the shear force is 50 kN, calculate the shear load per metre length at the top of the flangeof the T-section. [Start your calculations by setting the origin on the bottom of the cross- section].
i need the answer quickly
Q2/ Use the unit load method to find the slope and the horizontal displacement of point C on the frame shown below. E=200 GPa, I=200 x 10 mm 5 m B C 4 kN El 2 kN/m 6 m 1.5 EI A. For real load, horizontal reaction Ax= * Your answer For real load, vertical reaction Ay= * Your answer For real load, vertical reaction Cy= * Your answer For Unit load (horizontal displacement), horizontal reaction Ax= * Your answer For Unit load (horizontal displacement), vertical reaction Ay= * Your answer For Unit load (horizontal displacement), vertical reaction Cy= * Your answer
Q1) A simply supported beam is 3 m long and carries a vertical load of 5 kN at point 1m from the left-hand end. At a section 2 m from the left- hand end a clockwise couple of 3 kN.m is exerted, the axis the couple being horizontal and perpendicular to the longitudinal axis of the beam. The cross section of the beam shown in the figure. Determine the maximum bending stress set-up. 100 60 All dimensions in mm 100 70 30 EERI
Plot the Shear and Bending moment diagrams for the following. Use Singularity Functions to Solve the problem y 400 lbf Hinge | A B₁ AC R₂ R₁ 4 in 4 in 2 in 40 lbf/in 10 in D R3 X