If the sections shown below is subjected to a negative bending moment of 10kN, draw the 3D bending stress distribution. Please show all relevant calculations and values on your distribution. The position of the neutral axis is measured from reference point A

Q: Which of the following is closest to the moment of inertia (I) that would be used to calculate the…

A: Shear Stress =FAyINAbHere INA = MOI about the neutral axis.F= ForceA = area above the point Vy =…

Q: A a 90 B a G 30° b F b C

A: The values are

Q: Q4: If the cross section of the beam shown in the figure (3) below has bending stress of 28 MN/m² in…

A:

Q: Which moment(s) will produce bending stress at H? Select all that apply. y My HK Mx M Mx My Mz x

A: Only M_x will produce a compressive Bending stress at HExplanation:M_x will produce a Compressive…

Q: What is the maximum magnitude of the bending moment caused by force F? If none, enter zero. Do not…

A: The bending moment at point B can be determined as,

Q: For the beam shown, find the reactions at the supports and plot the shear-force and bending-moment…

A:

Q: see the image attached for the diagram thank you :) Determine the values and draw the diagram for…

A:

Q: 150 kN A 150 kN C D E 0.8 m 90 kN/m -2.4 m 0.8 m d B

A: To Find : The shear and bending moment diagram. Given : The F.B.D is,

Q: 2. The component shown always breaks at point C, which is just to the right of the contact point of…

A: The component always breaks at point C, which is just right of the contact point of the roller at B.…

Q: The shaft in the diagram below is subjected to bending forces of 8kN at B and 5 kN at C as shown in…

A:

Q: 8KN 2KN am 3m

A: given; w=2kN/m

Q: | A Wa a ! B w. b C x

A: 1) Given : a= 7 ft , b=8.7 ft , wa=13 kipsft , wb=7kipsft Concept used :  The conditions of…

Q: The compound beam is subjected to a unitorm dead load of 220 Ib/ft and a uniform ive load of 165…

A:

Q: There is no F1 or F2 force, only P against the front end of the beam. Thank you so much for any help…

A: Given data-P=5KN=5000Nσy=240 mPa=240 ×106 N/m2

Q: k P 0 8 ft x = 11.1 ft x RA 8. W (ft) Calculate the magnitude of the bending moment at distance x as…

A:

Q: Find the max shear stress in a 200mm tall, 150mm wide rectangular cross section using the…

A:

Q: Find the max shear stress in a 200mm tall, 150mm wide rectangular cross section using the…

A:

Q: B P = 10 kN L = 2.5 m 1.4 What is the value of the bending moment at x = 1.5 m?

A:

Q: Please answer the below using the same table layout I have.  I have attempted but I do not know…

A:

Q: In the figure shown, the aluminum strut has a cross-sectional area in the form of a cross. If it is…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.