Q2) For the circuit shown, calculate the:a) Total current flowing through the two supplies.Q+36v10k22kaob) Voltage at node a, Vac) Voltage at node b, V,[Ans: 6mA, 6V, -8V]6k48k3-12v

Answered: Image /qna-images/answer/feb03dd2-a3db-442b-8519-b990499e7724.jpg

Answered: Q2) For the circuit shown, calculate…

Q2) For the circuit shown, calculate the: a) Total current flowing through the two supplies. Q+36v 10k 22k ac b) Voltage at node a, Va c) Voltage at node b, V, 6k 48k 6k [Ans: 6mA, 6V, -8V] -12v

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

refer to the circuit below, a. what is the secondary voltage of the circuit (answer in Vrms) b. what is the DC current and rectified DC voltage across the load? c. what is the maximum current in the circuit? d. what is the direction of the DC current through the load?
With a D'Arsonval movement with 200 internal resistance and 100 mA FSD current, it is required to design an ammeter with a current ranges of 0.5 A, 3 A, and 5 A by using Ayrton shunt. Therefore, Rsh1 = Rhs2=............. Rh3=............
Parts a & b pls.
rical Circuits Lab. I and R. Use the term "propórtional" and "inverse proportional ", and X2- Give a definition of ohm's law for the three relationships between V, 4 1- Why dose the I-V characteristics pass through the origin? Discussion: also state the conditions for each individual relationship. tes. 3- Can you obtain practically the current passes through any circuit without using the Ammeter? Explain. 4- What is the difference between (P= I*V) and (P-I * R) ? 5- The circuit shown in Fig (1-5), calculates Requ, Vab12, Psupplied and P. consumed across (R4). RI 6- R1 R28.2 R2 (a) Parallel connection (b) Series connection Fig. (1-3) Resistors connection
5. A PMMC instrument gives 25mA at full scale reading when a potential difference across its terminals is 75mV. Show that how it can be used (a) as an ammeter for the current measurement in the range of 0-100A (b) as a 0 - 750V range voltmeter for the voltage measurement. Also, find the multiplying factor of shunt and voltage amplification.
: For the given circuit, transistors and diodes are silicon where VD₁=VD2=0.7V and |VBE|=0.7V. Neglect base currents. a) Calculate VB1, VB2 which are base to ground DC voltages of Q1 and Q2, respectively b) Calculate the power generated by source c) Calculate the maximum power delivered to load and conversion efficiency Show your calculations step by step and fill the table. (Or you can draw the same table in your answer sheet). No ▷ D₁ D₂ 1K Q₁ +20V C HH RL=1002 a) VB₁[V] VB2 [V] b) PDC [W] c) PL[W] Efficiency
Find voltage regulation in typing format please ASAP for the like
A 10-V independent voltage source is in series with a 2-A independent current source. What single source is equivalent to this series combination? Give the type and value of the equivalent source.
A battery is comprised of 4 cells connected in parallel, each cell has an EMF with 1.2V and an internal resistance of 0.55 ohm. There is no load connected to the terminals. Solve for Vterm.
1. The no-load terminal voltage of a battery is 30 V. The terminal voltage drops to 22 V when supplying a current of 5 A. Determine the emf and the internal resistance of this battery. Ans. r= 1.6 ohm 2. Two identical zinc carbon batteries are available. When connected in series, they supply 0.5 A to a 4 ohm resistor. When connected in parallel, they supply 0.4 A to a 5 ohm resistor. Determine the emf and internal resistance of each battery. Ans. 2.667 V and 3.333 ohm 3. When supplying a current of 5 A, the terminal voltage of a battery is 15 V. The battery is then recharged at a rate of 3 A and the terminal voltage is found to be 21 V. Determine the emf and the Internal resistance of the battery. Ans. 18.75 V and 0.75 ohm 4. A battery with an emf of 12 V and an internal resistance of 0.8 ohm is to be recharged through a 20 V source. (a) show by means of a diagram the connection of the circuit elements. (b) What is the current in the circuit? (c) The recharging current is to be…
V:19)
IN OUT GND V3 (1) R VR Consider the design of a DC power supply as shown above with the following requirements and constraints: • input from a 240 V RMS 50 Hz mains supply • diodes have a forward voltage drop of 0.6 V • utput voltage is required to be 9.1 V supplying a current of 575 mA • uses a 20:1 step-down transformer • the voltage regulator has a dropout voltage of 1.8 V In all of the questions below, give numeric answers correct to 3 significant figures and include units where required. Keep track of your intermediate results to more significant figures, otherwise rounding errors may lead to incorrect results. a. What is the peak voltage available at the secondary windings of the transformer? 数字单位 b. What is the peak voltage across the filter capacitor? 数字单位 c. What is the minimum allowable voltage at the input of the voltage regulator? 数字单位 d. What is the maximum allowable allowable ripple voltage across the capacitor? 数字单位 e. What is the minimum capacitor value that will…