Q2: Draw the construction details of a cantilever beam supported by one column to Scale 1:20 if: 1- Clear span= 3 m. 2- Supporting columns dimensions are 40 x 50cm. 3- Beam width = 40cm 4- Beam depth = 60cm at support end and 30cm at free end. 5- Tension Reinforcement: 6bars Ø20mm (one layer). 6- Compression Reinforcement: 2bars Ø20mm 7- Stirrups ø12mm @ 20cm in the first half part of span (near support) and @ 30 cm in the second half part of the span (one pace). 8- Concrete cover = 4cm.

Q2: Draw the construction details of a cantilever beam supported by one column to Scale 1:20 if: 1- Clear span= 3 m. 2- Supporting columns dimensions are 40 x 50cm. 3- Beam width = 40cm 4- Beam depth = 60cm at support end and 30cm at free end. 5- Tension Reinforcement: 6bars Ø20mm (one layer). 6- Compression Reinforcement: 2bars Ø20mm 7- Stirrups ø12mm @ 20cm in the first half part of span (near support) and @ 30 cm in the second half part of the span (one pace). 8- Concrete cover = 4cm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please solve part A and B Subject is reinforced concrete design show all steps
feu = 40 MPa Cover = 3smm fy = 500 MPa fy = 250 MPa Preferred link size = 10mm Question 2 Design the reinforcement for the following one-way slab: Slab thickness,h= %3D 160 mm Design Mid-span Moment, M = 35 kNm Preferred bar sizes = main bar: 12mm; distribution bar: 10mm Q2a. Calculate the steel area required (in mm2per m width). Q2b. Provide main bars and distribution bars.
Q2/ Determine the amount of steel required to create a balanced condition for the beam that has height 500 mm, width 300 mm, effective depth (d) 450 mm as shown in figure 2, where f'c 25 MPa and fy = 400 MPa. (50 marks) %3D 300 mm 500 mm Figure 2
need asap. please be detailed with your solution and box the final answer.
For the following plan it is required to: 1- Design all beams for flexure and shear, where they have additional 30 kN/m distributed factored load 2- Design the columns. The concrete has a strength of 30 MPa, and the yield strength of the steel is 420 MPa. Show full calculations and neat sketches. All dimensions are in m. I 03 B2 0,3 7 B1 Wu=20 kN/m2 B1
A concrete floor slab measuring 6 m x 3 m is simply supported on one side brick load bearing walls along the 6 m sides. The concrete slab is 200 mm thick and reinforced at the bottom as follows.1. Main reinforcement (short span i.e the bars are parallel to the short span), Y 12, shape code 34 @ 125 mm centre to centre,2. Distribution reinforcement (long span i.e the bars are parallel to the long span), Y 10, shape code 20 @ 300 mm centre to centre,3. Concrete cover, 30mm,4. Concrete strength, 40MPa.Draw the reinforcement layout for this slab, in plan and section, indicating all the reinforcement and necessary information required by the contractor. You must calculate and indicate the number of bars required on your drawing. You do not need to calculate the bar lengths and the curtailment. Your drawing must be neat.
Given a concrete column that would be required to support loads of Pu=400kips and Mu=50 kip-feet, we will determine the column interaction curve and decide if the column is adequate for this particular application. The column will be a 14”x14” square, tied column with #9 bars at the corners. The center of the reinforcement in each corner is 3” from each of the sides. The f’c of the concrete is 4 ksi and the reinforcement is Grade 60. Determine if the column is acceptable for this application. Calculate the value of Mu and Pu.
4.3 A simply supported beam is reinforced with 5-ϕ25 mm at the bottom and 2-ϕ20 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc’= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Calculate: Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = _____?____ kN/m (to the nearest whole number)
1. A two span beam subjected to shear and flexure only is reinforced as follows: SECTION: TOP BARS @ MIDSPAN: 2-⌀20mm @ FACE OF SUPPORTS: 5-⌀20mm SECTION: BOTTOM BARS @ MIDSPAN: 3-⌀20 mm @ FACE IF SUPPORTS: 2-⌀20 mm Given: Stirrup diameter, ds = 10 mm Concrete f'c = 21 MPa Steel rebar fy = 415 MPa Stirrup fy = 275 MPa Beam size b x h = 270 mm x 450 mm Assume all bars laid out in single layer. Calculate the following: a. Design Moment strength of section at midspan for positive bending = ______ kN·m (nearest whole number)
QUESTION 1A concrete floor slab measuring 6 m x 3 m is simply supported on one side brick load-bearing walls along the 6 m sides. The concrete slab is 200 mm thick and reinforced at the bottom as follows. a. Main reinforcement (short span i.e the bars are parallel to the short span), Y12, shape code 34 @ 125 mm centre to centre,b. Distribution reinforcement (long-span i.e the bars are parallel to the long span), Y 10, shape code 20 @ 300 mm centre to centre,c. Concrete cover, 30mm,d. Concrete strength, 40MPa. Draw the reinforcement layout for this slab, in plan and section, indicating all thereinforcement and necessary information required by the contractor. Calculate and indicate the number of bars required on your drawing. You do not need to calculate the bar lengths and the curtailment. Neat drawing please
Problem No. 3 A beam 200x45Omm is reinforced by 2-32mm diameter rebar. Assume cc=50mm, stirrups=10mm, fc'=21Mpa and fy=415Mpa. Calculate the following. 17. Calculate the strain of the steel reinforcement 0.00182 O 0.00201 O 0.00224 0.00391 O 0.00577