Q2) Consider a unity negative feedback control system with an open 1oop4transfer function GH (s) =Let the input signal be r(t) = A u(t),where A is a constant. Find A so that the steady state output is yss(t) = 10%3Ds+1

Answered: Image /qna-images/answer/876a8045-dcdf-4531-bbfe-3554bffddfa8.jpg

Q2) Consider a unity negative feedback control system with an open 10op transfer function GH (s) = 4 Let the input signal be r(t) = A u(t), s+1 %3D where A is a constant. Find A so that the steady state output is yss(t) = 10

Q2) Consider a unity negative feedback control system with an open 10op transfer function GH (s) = 4 Let the input signal be r(t) = A u(t), s+1 %3D where A is a constant. Find A so that the steady state output is yss(t) = 10

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please show work
Please provide Handwritten answer
(b) Figure Q3(b) shows a phase shift oscillator circuit. Given the feedback gain: V1 1 = (s)g V2 (sRC)3 + 5(sRC)² + 6(sRC) +1 R2 R1 ww V2 ww Figure Q3(b) (i) Determine an equation for frequency of oscillation. Calculate the value of capacitors, C, if the output voltage is equal to 5 sin 3t V and resistor, R is equal to 100 k. (ii) (iii) Calculate the open-loop gain, A, in order to generate an oscillating signal. Determine the value for R1and R2 in order to generate an oscillating signal. You may refer to the Appendix in page 5 and 6 for the commercial value of resistor. (iv)
Q.4. Consider a unity feedback control system with feed forward :transfer function is .Q.4 G(s) 12(s+2.5) s (s² + 5s +11) A) It is desired to make the damping ratio (5) of the dominant closed-loop poles equal to (0.5) and to increase the undamped natural frequency (w) to (5 rad/sec) and the static velocity error constant to (K, = 60 sec-1). Design an appropriate compensator to meet all the performance specifications.? B) Check the stability of this system with compensator and without it? (
A feedback system has the closed loop transfer function shown below. Find K2 so that the settling time t,=0.2 seconds for a 1% tolerance. C(s) R(s) 100K1 20s(1 + 0.5s) + 100K1+(100)(20)K25
A unity feedback system has the following open loop transfer function G(s) = 100(s+5)/(s+2)(s+4) Determine the following steady state error values: A. e(step) B. e(ramp) C. e(parabola) Leave all answers round to TWO decimal places
Copy the control system shown in Figure Q2 into your answer book, labelling the actual output, control signal, desired output, plant, feedback and error signal. Q2 (a) 2 Σ K+ K, (s+1)(s+2) Figure Q2 (b) Determine the closed-loop transfer function for the system shown in Figure Q2 and hence obtain the characteristic equation for the system. Using Routh 's stability criterion, find the range of the controller gains (K, Ki) for which this system is stable. (c) For the system shown in Figure Q2, find the frequency, jo, and gain, Kı, for which the root locus crosses the imaginary axis (assume K = 1). (d) (e) What would you expect to see for the frequency, calculated in part (d), when you decrease K below 1.
Please answer all subpart either dislike is ready please all subpart please Asap I will like it please...
Suppose that one design specification for a feedback control system requires that the percent overshoot to a step input be less than 10%. The corresponding specification in the frequency domain is Select one: O a. Mp ≤ 0.55 O b. Mp 1.05 C. Mp ≤ 1.27 O d. Mp ≤ 0.59
Q.2) For the below unity feedback system shown in figure a, M(s) is added (as shown in figure b) to make an error at the steady-state to be zero, if you know that the input R(s) is a a- Unit step b- Unit ramp c- Unit-parabolic Evaluate M(s) which perform the mentioned function? R(s) G(s) C(s) R(s) G(s)H M(s) C(s) (а) (b)
Q.2) For the below unity feedback system shown in figure a, M(s) is added (as shown in figure b) to make an error at the steady-state to be zero, if you know that the input R(s) is a a- Unit step b- Unit ramp c- Unit-parabolic Evaluate M(s) which perform the mentioned function? R(s) G(s) C(s) R(s) G(s) E M(s) C(s) (a) (b)
ASAP