Q2/ Calculate the bending moment capacity of an interior simply supported T-beam of (Length = 7.0m) that support reinforced concrete floor slab of 75mm (slab thickness). If the space between reinforced concrete beams is 1.5 m face to face have, the effective depth = 538 mm, web width =300mm, steel reinforcement As -4#25 mm, fc =28 MPa, fy = 420 MPa. -7.0 m- As4D 25 mm 1.50 m A40 25 mm 1.50 m As-40 25 mm 1.50 m

Q2/ Calculate the bending moment capacity of an interior simply supported T-beam of (Length = 7.0m) that support reinforced concrete floor slab of 75mm (slab thickness). If the space between reinforced concrete beams is 1.5 m face to face have, the effective depth = 538 mm, web width =300mm, steel reinforcement As -4#25 mm, fc =28 MPa, fy = 420 MPa. -7.0 m- As4D 25 mm 1.50 m A40 25 mm 1.50 m As-40 25 mm 1.50 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

only need solutions Im confused ty ANSWER: Mu = 535.44038 kN-m
Q4/ Compact the design bending strength to the reinforced concrete beam has a width b=300mm and effective depth d=525mm, fc-20, fy=300MPa. Suppose that the beam design to achieve a maximum bending according to code.
Determine the required steel area for a T-beam that traverses the center of a floor system for which bw = 300 mm and d = 550 mm. The beams are 4.8 m long and spaced at 3 m. O.C. The slab thickness is 100 mm. Mp = 400 KN-m (including its own weight), ML = 500 KN-m. f'c = 28 MPa, and fy = 414 MPa
A composite beam is fabricated by bolting two 3.6-in.-wide by 13-in.-deep timber planks to the sides of a 0.5-in. by 13-in. steel plate. The moduli of elasticity of the timber and the steel are 1700 ksi and 29000 ksi, respectively. The simply supported beam spans a distance of 25 ft and carries two concentrated loads P, which are applied as shown. Assume LAB = LCD = 7 ft, LBc = 11 ft, b = 3.6 in., d = 13 in. and t = 0.5 in. (a) Determine the maximum bending stresses o,,o, produced in the timber planks and the steel plate if P = 3.7 kips. (b) Assume that the allowable bending stresses of the timber and the steel are 1010 psi and 26800 psi, respectively. Determine the largest acceptable magnitude for concentrated loads P. (You may neglect the weight of the beam in your calculations.) Answers: LAB (a) o, = (b) P = i i B LBC b F لالها b Cross section C kips. d ksi, o, = LCD D ksi.
A reinforced concrete T-beam is to be designed for tension only. The beamwidth is 250 mm. effective depth to bottom bars is 400 mm, flange thickness is 100mm, simple span is 3.6 m and beam spacing is 1.2 m on centres. If the applied designmoment is 300 kn-m, fc’ = 20.7 MPa and fy = 414 MPa. Determine the effective widthof the compression flange and the number of 28 mmφ diameter bars necessary forthe beam.
Answer fast
A rectangular cross section of a beam is under the bending moment of 60 kips-ft. Determined the Maximum compression and tension stress in the concrete and tensile stress in the rebar. The section is uncracked. b-15 in, h=30 in, d= 28 in f=4000 psi, Ec-3,600,000 psf fy= 60,000 psi, Es-29,000,000 psf Rebar= 3 -No. 6 h -As
A continuous concrete beam shown in the figure has a width of b= 300 mm, an effective depth of d= 560 mm, and an overall depth of h= 600 mm. Concrete compressive strength fIc=21.0 MPa and steel yield strength fy= 275 MPa. The beam carries a superimposed dead load at span AB of 7.5 kN/m and at span BC, CD of 4.5 kN/m. A live load at span AB of 12.5 kN /m and at span BC, CD of 10.5 kN/m. Determine the number, N, of 20 mm ∅ deformed steel bars at the following sections1) support A 2) Support B 3) Support C4) between AB 5) between BC
I need the answer to the question in reinforced concrete
AT-Beam has the following properties: bf = 750 mm, bw = 275 mm, d 560 mm, t = 115 mm. Concrete compressive strength fe 21 MPa and steel yield strength fy 415 MPa. T-Beam is under factored moment load of 720 kN-m. Locate the compression block under balanced condition from the extreme compression fiber.