Q2: A/ The full-wave controlled bridge rectifier of has an ac input of 200 V peak to peak at 50 Hz and 7 ohm load resistor. The delay angle is 45 degree. Determine the average current in the load, the power absorbed by the load, and the source volt amperes, draw the circuit

Q2: A/ The full-wave controlled bridge rectifier of has an ac input of 200 V peak to peak at 50 Hz and 7 ohm load resistor. The delay angle is 45 degree. Determine the average current in the load, the power absorbed by the load, and the source volt amperes, draw the circuit

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What will be the out put of the D'Arsonval meters, if an average responding a.c meter of half-wave rectifier read (236 v), and true form foctor of input waveform is (114). *
Design a full-wave bridge type power supply. Design the transformer, filter and regulator section. For the rectifier part, choose diode with appropriate PIV rating. Use standard values for your design. The output dc voltage should be 7.5 V and the Maximum output power be 20 mW.
(i) Draw the circuit diagram of single phase fully controlled bridge rectifier with RL load and write the current path for negative half cycle operation. (ii) Plot the output voltage and current waveforms for firing pulse is 60° .
2. A circuit of 3-Phase Controlled Half Wave Rectifier with Resistive load is as below. A T2 eleeeeee B If the firing angle, a are to set at r/9, complete the circuit operation for the whole cycle (0° to 360°) for the period stated in Table 1. By using appropriate scale, draw a waveform of Average Output Voltage, Vo(avg). Derive an equation for the average output voltage, Vo(avg). If the rectifier is connected to 208V, calculate the Vo(avg) if the load is purely resistive. (C3, CLO1) Duration Period s1 S2 S3 Vout 1 0° – 20° 20° – 50° 3 50° – 120° 4 120° – 140° 140° – 170° 170° – 240° 7 240° – 260° 8 260° – 290° 290° – 360° Table 1
A full-wave rectifier produces a 32V peak rectified voltage from a 50Hz ac source. Determine the filter capacitor needed to provide a DC output voltage 24V across a 500 ohm load.
write clean and descriptive
Draw the form of bridge type full wave rectifier power source consisting of 4 layers (lowering, rectifier, filter, regulated) and briefly explain the role of each layer (by drawing the signal entering the layer and the signals coming out of the layer).
Solve each one with steps.
A full-wave rectifier produces a 32V peak rectified voltage from a 50Hz ac source. Determine the filter capacitor needed to provide a DC output voltage 24V across a 500 ohm load.
Consider the full-wave bridge rectifier circuit. The input signal is 120 V (rms) at 60 Hz. The load resistance is R250. The peak output voltage is to be 9 V and the ripple voltage is to be no more than 5 percent. Determine the required turns ratio and the load current. Note: please solve within 30 minutes. Avoid plagiarism.
Question 1 a) Compare the holding current with the latching in SCR. b) A 400 V/50 Hz three-phase system is loaded with an ideal three-phase diode rectifier having a completely smooth output current of 50 A. An ideal three-phase thyristor converter is connected in parallel with the diode rectifier. The output current of the thyristor converter is also 50 A and completely smooth, but the output power of the thyristor converter is zero. i. Draw the waveforms of the input currents to the two converters and the the sum of the two currents. ii. Calculate the power factor for the total load. c) The shown converter in Figure 1 operates in continuous conduction mode. Assume the components are ideal. i, (1) in (t) v ic (t) Vo (t) iL (t) +v (t) - is (1) "; (1) Figure 1 i. Sketch of i (t) and VL(t) for one switching period Ts. ii. Determine the DC voltage gain Vo/Vg as function of duty cycle, D.
-,- three phase half wave controlled rectifier with resistive load (R=10 2) if the input supply voltage is (Vrms = 380 Volt and f= 50 Hz) and the trigger angle (a = 60°), then determine the followings:- a) Draw the rectifier circuit. b) Draw to scale the input voltage, the load voltage and the current waveforins. c) Calculate the average value of the output voltage.