a)on the bridge type Full wave rectifier circuit given in the figure + / - draw current voles for each of the alternans. b) the waveform of the output voltage Vç is given in the graphs on the side 311v VI -311v draw in space and calculate the peak value and specify it on the chart. + 13v V2 c) calculate the effective value of the output voltage. (Vç (eff)=.... ? ). -13V Note: Diodes are not ideal. =0.7 V. DI D2 Vin D D4

Q: With neat diagram explain the parts of galvanometer

A: The galvanometer is the device used for detecting the presence of small current and voltage or for…

Q: 4. a) Explain the issues to be considered in the location of wind energy systems. b) Draw the block…

A: Wind turbine locations are very important for successful operations of wind power plants. The…

Q: What do call to the encircle part of socket and what is the purpose?

A: It is a 3 pin plug. There are three wires in a 3 pin plug named as- 1 – Earth -E 2 – Neutral -N 3 –…

Q: brownout is defined as: a slightly decreased voltage lasting from seconds to minutes or more

A: In this question we will define brownout in power system....

Q: Describe the functions of earthing/grounding in providing safety to user when a live wiretouches the…

A: Earthing: Earthing/ grounding is of low resistance wire and high melting point which prevents from…

Q: 21/ Which Insulators can be used for both horizontal and vertical positioning? A. PIN TYPE…

A: Given  Which Insulators can be used for both horizontal and vertical positioning?

Q: Explain insulation coordination

A: Coordination is required in electrical systems for proper functioning of the equipments. Insulation…

Q: Which of the following meters have a linear scale? a. Moving iron meter O b. Moving coil meter O c.…

A: Non linear scale is because of torque pruduction is due to square of current . Due to non linear…

Q: List the different Wire Gauge and its uses. Note: Typical wires at home.

A: The wire gauge is used to measure the diameter of the wire. The measure of electric flow the wire…

Q: Multiple Choice. Refers to a point in a circuit where three or more wires are connected. A.…

A:

Q: A conductor has an initial diameter of 0.175 inch and a resistance of 0.5 ohm. If the wire is drawn…

A:

Q: What is UPS in electrical engineering?

A: Full form of UPSUninterruptible power supply

Q: Explain with neat diagram of any one solar energy thermal application.

A: SOLAR WATER HEATERS:- The Solar water heaters are comparatively easy application of solar thermal…

Q: Explain the working of the Potential meter float gauge with a neat diagram

A: Draw the Potential meter float gauge: Based on the displacement of the float, the float gauge…

Q: Discuss any two types of grounding methods.

A: Two types of grounding methods: Solid grounding Resistance grounding

Q: What is voltage reference?

A: A voltage reference is an electronic device designed to maintain an accurate, low noise. It ideally…

Q: Choose the correct answer 5-  ________ related ranging errors to the dispersion in measured…

A:

Q: s an Electrical Safety person, exposed wires should be recognized as a hazard. Evaluate the risk…

A: In an electrical system, an exposed wire can a person in a situation of danger. Exposed wires may…

Q: Explain the Different types of testing Methodologies used in CB??

A: To check the rated characteristics and the capabilities of a circuit breaker, different types of…

Q: Which Insulators can be used for both horizontal and vertical positioning? A. SUSPENSION TYPE…

A:

Q: 4. Bus bars are either flat tubes as these shapes allow heat to or dissipate more efficiently.

A: The size of bus bar determines the amount of current flows through it safely. The heat dissipation…

Q: Part 2: Analysis and selection of the Wind Turbine. The team decides at install a 30 MW wind farm.…

A: 1: Analysis and selection of the Wind Turbine.The team decides to install a 30 MW wind farm. The…

Q: What is the branch circuit protective device?

A: Branch circuit protective device is used to protect the motor winding and insulation if due to some…

Q: Q.6 a) Name and explain the process to join any electrical component on strip board. b) List the…

A: 6. (a) Soldering is the technique used to connect any electrical component to a strip of circuit…

Q: Draw the block diagram representation of a heating system.

A: Answer- Block diagram of heating system -

Q: 1. The practical unit of electric charge. ____________ 2. A path for the current to flow.…

A: In these questions,  Fill the blanks Unit of electric charges, path of current flow,  DC voltage…

Q: Discuss briefly the classification of electrical heating method

A: The classification of electrical heating method:

Q: How equation is obtained ? is that equation given in the textbook ?

A: That equation is the direct formula of pulse spread. And no need of derivation of the equation.…

Q: In a PT100 Resistance Temperature Detector, the resistance of the RTD is 100 ohms at _______ °C?

A: Given here a PT 100 resistance temperature detector, and asked what is the temperature of RTD at 100…

Q: A cone meter rod 2 cm diameter is drawn until its resistance is 100 times the initial resistance.…

A: Given : In the given question they have mentioned a resistance is made from a cone of diameter…

Q: Compare the resistance limit of the switch (based on specification) and the computed total…

A: According to the question, we need to compare the resistance limit of the switch (based on…

Q: Fill in the blank: Electrical hazard boots are made up of highly materials.

A: Electrical Hazard boots are used to prevent the shock

Q: Looking at several older cars that are showing initial signs of rust formation, where do you expect…

A: In older cars there are various areas which is exposed to water and atmospheric salts and these are…

Q: Q1) Fill in the blanks by inserting appropriate words/numbers 1- The low value of k in voltage…

A:

Q: This is a general question: How do smaller electrical engineering labs relate to building a…

A: Smaller electrical engineering labs can be very helpful in building a relatively larger system. This…

Q: Q6) Explain by drawing a block diagram of a power supply?

A: Draw the block diagram of the Regulated power supply.

Q: Make a research question regarding with these topics A. Solar Powered Light Post B. Underground…

A: Different energy sources are required in day to day life. These energy sources can be renewable or…

Q: What does the circuit work like?

A: The above question is based on the firing circuit of a TRAIC.

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.